Answer / venkatesh b.k

Once the two wheeler is started , the fly wheel begin to
rotate with the help of starter, which in turn will be
connected to the crank shaft of the engine.. so crank shaft
will rotate which moves the piston and the engine starts.

Answer / rakesh kiran

when we kick we actually rotate the flywheel which is
mounted on the crankshaft, due to cranking piston
reciprocate and compress the air-fuel mixture and spark
plug ignites the mixture and the vehicle get started........

Answer / shashank kumar

when kick the kicker. rotate the flywheel when flywheel
power go to the crankshaft due to cranking afert the crank
shaft power to the the piston and after piston is
recipocate to TDC to BDC the workes is started like;
section,Compress, Power & Exhust the engine is started.

Answer / bhanu pratap

when v kicked it rotate the crack shaft which connected with piston & piston started storking then engine became start.

Answer / kavin kumar

The kicker get engaed with
the clutch (or) fly wheel
and cranks the engine the
rotating motion is
developed,where the crank
shaft is coupled with
ignition coil due to the
voltage produced in coil is
transfered to spark plug it
ignites the fuel and air in
compression (tdc) ,the
expansion takes place
(these all happends within
a second)...the as we
release the kicker it
disengaed. and the engine
runs ....

Answer / satheeskumar

when we kick the kicker the piston engine is tend to go for the strokes while that time energy is produced and the engine starts running continuously

Answer / p.immanuel

when we kick the kicker, the piston is being activated by flywheel thro crank shaft and connecting rod ,and when the piston moves from TDC to BDC, vacuum is created in side the cylinder that sucks the charge thro inlet port, and compression , power and exhaust stroke are continued

Answer / kalandar naina mohamed.a

when we kick the kicker, the piston is being activated by flywheel through crank shaft and connecting rod ,and when the piston moves from TDC to BDC, vacuum is created in side the cylinder that sucks the charge through inlet port, and compression , power and exhaust stroke are continued

Answer / santosh

whn v hv a self, current fr. battery goes 2 d motor(dats dc motor) which in turn drives d flywheel, which is attached 2 d crank via pinion n ring arrangement

Answer / saravanan

due 2 spark plug

Tell us about the working of a 6-stroke engine.

0 Answers   Ashok Leyland,

Does diesel engine powered automobile use unit pump and unit injector?

0 Answers  

What is sae?

0 Answers  

prove the relation for the torque required in order to accelerate a gered system?

0 Answers   TATA,

The resistance to the vehicle motion whose magnitude various with the square of the vehicle speed is a) Resistance due to gradient b) Resistance due to road c) Resistance due to the tyre friction d) Resistance due to wind

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,

can we start the diesel engine with petrol and petrol engine with diesel?(just start not run)

7 Answers   Ford, Honda, PSR Engineering College,

Why oil with petrol can be used in two stroke engines but not in four stroke engines (two wheelers)?

0 Answers  

Why I/P transducer is connect with 24V DC not to 220V AC?

0 Answers   L&T, TATA,

why we use ignitor in ignition coils in automobile sector?

2 Answers   DE Diamond Electric India,

1) can any one tell how dozer transmission system power terrain --track

0 Answers  

Explain different between two stroke engine four stroke engine?

0 Answers  

Propeller shaft is used for the purpose of a) Transmitting the drive from the transmission to the bevel pinion of the final drive b) Transmitting the drive from the crankshaft to the road wheels c) Transmitting the drive from the transmission to the road wheels d) Transmitting the drive from the crankshaft to the bevel pinion of the final drive

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,