Interested to Buy Any Domain ? << Click Here >> for more details...
Bridges work at what layer of the OSI model?
A.) Data Link
B.) Network
C.) Physical
D.) Application
- 12 Answers
- 63182 Views
- KVS, PGT, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / guest
Answer: A
Bridges work at Layer 2 (Data Link) because they examine the
MAC address
of the packet which they base decisions upon.
| Is This Answer Correct ? | 176 Yes | 6 No |
Answer / rozy saluja
data link layer because bridges inspect incoming traffic
and decide whether to forward and discard it.
| Is This Answer Correct ? | 16 Yes | 1 No |
Answer / vijay kumar sharma
data link layer b/c it it examin the incoming address from network layer
| Is This Answer Correct ? | 13 Yes | 3 No |
Answer / zeeshan ali
My answer is
A bridges function in the Data Link
| Is This Answer Correct ? | 10 Yes | 1 No |
What is passive topology in ccna?
What is the default bandwidth of a serial connection? A.) 1200 baud B.) 1.544 Mbps (T1) C.) 10 Mbps D.) 96Kpbs
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)# router igrp 100 Router(config-router)# network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
Identify the 2 characteristics regarding MAC addresses? A.) Contains a network portion and host portion B.) Always assigned by System Administrator C.) 48 bits long D.) Contains a vendor code and serial number
Which statement is true regarding the user exec and privileged exec mode? A.) The '?' only works in Privileged exec B.) They are identical C.) They both require the enable password D.) User exec is a subset of the privileged exec
In which access- list type you can't do editing?
Mention what is dhcp?
Identify the default encapsulation on serial interfaces? A.) ISDN B.) HDLC C.) SDLC D.) Frame Relay E.) PPP
Which layer is responsible for determining if sufficient resources for the intended communication exists? A.) Application B.) Network C.) Session D.) Presentation E.) Transport
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
Which OSI layer supports the communication component of an application? A.) Data-Link B.) Physical C.) Session D.) Presentation E.) Application F.) Transport
Which processes does TCP, but not UDP, use? A. Windowing B. Acknowledgements C. Source Port D. Destination Port
CCNA 
