Answer / jt

correction

US (North America) use 60Hz not 100Hz.

Answer / eduardo

I don´t know, but I think it is because all European
countries use 230 V 50 Hz.
I think India is now 230 V and not 220 V (as in Europe).
And in American continent is 60 Hz not 100Hz

Answer / shafeeq

A lot of points are factored when a utility decides to
choose 50 or 60 hertz, sometimes it may even been a
political rather than a technical one. We have seen various
types of wars on measurements types of units used or have
been an interested but an innocent invitee in format wars
in electronics like 8 track v/s cassette, v2000 (an
excellent system) V/s the betamax (also with some notable
features) and the vhs. Now we are also extended into the
video disc formats. However if we were to look closely many
of us will agree that 60hz is a good choice. All inductors
and motors could be smaller, and the benefits will
encompass a wide array of electrical and electronic goods
to which the changes will almost be transparent. But it
should be noted that most critical and large capital
intensive plants and machinery, including certain medical
equipment, will not take too kindly to such a change,
which, besides straying from the critical specs, or worse
still may give up altogether, unless expensive time
consuming replacement or an equally complicated and
efficient cycle converter is installed before the system is
connected to the mains.

As a historical note, 60Hz was originally chosen in the US
to help market AC power systems to customers. The ploy was
that a clock could run using a synchronous AC motor and at
60Hz, the gear mechanism would be greatly simplified. Then
the job of keeping accurate time fell to the electricity
company by maintaining a constant frequency. Prior to this,
many different frequencies had been tried.

As regards 50 Hz in India it is descendant of the British
Imperial system. Technically speaking operating 50 Hz
versus 60 Hz would not make much difference but, to achieve
it, either the prime movers - for example steam turbines,
gas turbines and diesel engines - would need to be able to
tolerate a 20% increase in speed or the alternators they
drive - which produce the electricity - would need to be
completely rebuilt with extra poles and windings so that
they could continue to run at the same rotational speed.
The costs of doing such re-engineering would be enormous
and could not be justified as "economically worthwhile"
from the point of view of actual necessity, quite apart
from the severe problems which would be caused to assuring
operational continuity of service whilst such changes were
made.

Further, for any load equipment - machines, appliances,
etc. - that have reactive components
(capacitors/inductors), the effects of a frequency change
from 50 Hz to 60 Hz on such impedances would not be trivial
and would significantly alter their in-circuit behaviour.
This means changes would have to be made to the sizes all
such reactive components to achieve the same effects at the
higher frequency. Doing that would be yet another enormous
cost of conversion from 50 Hz to 60 Hz which could not be
justified as economically worthwhile.

Answer / kingshuk dey

There is actually no reason! 220V, 110V, 24V all are available voltages. India was once a British colony and hence, the power system started with the standards the British were following during their time. Now if we change, the existing power plants will become useless. Hence, to maintain continuity, 220V 50Hz is being used.

The Indian Railways power outlet works in 110 Volt, almost all electrical control systems are designed for 110 Volt or 24Volt.

Ideally, the safest voltage to use is anything under 24 Volt AC, like 12VAC, 5VAC. The lower the better, as it will lower the chances of getting electrical shock, and consuming less power.

Anyways, just as a matter of fact, more work can be done for less power using 60Hz than 50Hz (energy remaining constant).

Answer / saravanan

india power generation eqpiments rating standard is 50 Hz,&
220v (single phase).in us system is 100Hz & 110v. in this
method no save power

If we have a 2000kva load,How much kvar capacitors we go to add to improve the power factor at 0.9?pls give the calculation and fully theory?

2 Answers   ABB, Unitech,

Why should be the frequency 50 hz 60hz only why not others like 45, 95 56 or anything , why should we maintain the frequency constant if so why it is only 50 hz 60hz?

0 Answers  

give single line diagram of D.G distribution form alternator to main L.T panel?

0 Answers  

How to select the earthing transformer,for DELTA TO DELTA TRANSFORMER OR ALTERNATOR SIDE.Pls post your answers and calculation.

0 Answers  

How calculate the Transformer Impedence With Example

3 Answers  

whats is MARX CIRCUIT?

1 Answers  

Why inverter rating in KVA?

3 Answers  

What is limitedly stable system?

0 Answers  

From what on-site components does the HT panel monitoring the bus-bars in a 11kV system take inputs?

0 Answers  

can anybody tell me that for p.f. Improvment we use capacitor banks but how to decide its capacitance. As we all know how to calculate kvar but what abt capacitance value

0 Answers  

why transformer rating is always in KVA

7 Answers   GNG, NTPC,

What is stepper motor?

0 Answers