Answer / jitender(abb)

hi
This is Jitendera here.look which institute you are going to join it doesn't have any matter the matter is that how much you are devoted towards subject.a teacher can guide u only but u have to read and u have to struggle from yours difficulty.look a man only learn from his mistake.
so at first what ever you have facing the problem you have to figure it out.
the solution after when you fail then only u can ask with urs teacher.
believe me this is a good method of learning.

any how after completing urs course u have to come on market and there is competitions

so u have to be the up to average not average.


so my suggition is that join any institute and teach urs self

Answer / dharmendra soni

I think Right
jiterdra is telling good answer so you should be depends
upon self.But whenever u come to delhi frist u try best
insitute think u get it .

Answer / bharat

Hi,
I suggest topgun technologies bangalore its faculty is quite good and there success rate for ccie passouts is highest in india I myself am the student of topgun and experience is satisfying I cleared my ccna on 18 may 2010 score 987/1000 best thing about it is they focus on good studies rather than you passing the exam by cramming dumps

Which Cisco IOS command should you use to display the Novell IPX address assignments on a router? A. show ipx addresses B. show ipx interface C. show me the money D. ipx, network (number) E. display ipx addresses F. show ipx routing details

1 Answers  

---

What is switch priority & why it is used????

5 Answers   ADP,

---

Can anyone explain the STP Security features. Just like BPDU guard, Root Guard. Hi JITENDERA, i m specially looking for u?????

2 Answers  

---

Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0

2 Answers   Accel, CMS,

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

Which layer is responsible for providing mechanisms for multiplexing upper-layer application, session establishment, and tear down of virtual circuits? A.) Session B.) Network C.) Physical D.) Transport E.) Application F.) Presentation

1 Answers  

---

Can you define in short what VPN is?

5 Answers   CCIE,

---

How is rip different from igrp?

0 Answers  

---

what is the purpose of multicast packets?

2 Answers  

---

LMI operates between the Frame Switch and what other device? A.) CPE device B.) Another Frame Switch C.) X.25 switch D.) Novell File Server

2 Answers  

---

What is the UDP datagram format? A. Source Port - 16 bits, Destination Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data B. Destination Port - 16 bits, Source Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data C. Source Port - 16 bits, Destination Port - 16 bits, Checksum - 16 Bits, Length - 16 bits, Data D. Source Port - 8 bits, Destination Port - 8 bits, Length -8 Bits, Checksum - 8 bits, Data

1 Answers  

---

Hello every one. Please can any one explain me the difference b/w Cisco Switch/ws-c3560-24ps-s and Switch/ws- c3560-24ts-s. what is does PS & TS Stands for. Waiting for your passtive reply. Wish You all the best

2 Answers  

---