which utility should use to test whether TCP/IP has been
initialized on a system.friends plz post the answer with
explaination..

Answers were Sorted based on User's Feedback



which utility should use to test whether TCP/IP has been initialized on a system.friends plz post t..

Answer / vivek

PING

to check TCP/IP has been
initialized
PING 127.0.0.1

If you +ve Replay from that ,,then ur TCP/IP has been initialized correctly.......

Is This Answer Correct ?    5 Yes 0 No

which utility should use to test whether TCP/IP has been initialized on a system.friends plz post t..

Answer / niraj mishra

using loopback testing we can check TCP/IP initialization
.........

Is This Answer Correct ?    1 Yes 0 No

which utility should use to test whether TCP/IP has been initialized on a system.friends plz post t..

Answer / srikant kumar

It will be Ping 127.0.0.1

It verify the our TCp/IP setttings.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

Using the access-list command, 'access-list 1 deny 2.2.2.2', what else must be done to stop host 2.2.2.2 from sending any traffic out of physical interface E0, while still allowing other traffic? A.) In global mode, Add a line - 'access-list 1 permit 0.0.0.0 255.255.255.255' B.) On interface E0, Add a line - 'access-group 1 in' C.) In global mode, Add a line - 'access-list 1 permit all' D.) On interface E0, Add a line - 'access-list 1 in' E.) On interface E0, Add a line - 'access-list 1 out' F.) On interface E0, Add a line - 'ip access-group 1'

1 Answers  


When using access lists, what does a Cisco router check first? A. To see if the packet is routable or bridgeable B. The destination address C. The source address D. The packet contents

1 Answers  


Identify the 2 types of access-list filters that control SAP traffic? A.) Novell-ether B.) Arpa C.) Input-sap-filter D.) Round-robin E.) Output-sap-filter

1 Answers  


Define class full protocol?

0 Answers  


What is the routing algorithm used by RIP and IGRP? A.) OSPF B.) Link-state C.) Dynamic D.) Distance Vector

3 Answers   Cisco,






How does rip differs from igrp?

0 Answers  


Urgent reply plz donot have time to serch on google plz reply the questions is how to remove newfolder.exe virus from my windows 2003 server i have all ready tried quick heal.spy hunter mcafee server . plz reply

4 Answers  


Identify the X.25 addressing standard? A.) X.121 B.) X.25a C.) ITU-1 D.) Q933a

1 Answers  


What is the command to copy the IOS image to a TFTP server? A.) copy flash tftp B.) copy running-config tftp C.) copy ios tftp D.) copy startup-config tftp

2 Answers  


hello friends im murtaza frm indore... and my question is that im doing hardware engenering and networking and im intrested in make a good career in networking so can you suggest.. which institiue is good for me...plzzz replyy im waiting...

1 Answers  


The following is partial output from a routing table, identify the 2 numbers in the square brackets; '192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1' A.) 100 = metric, 1300 = administrative distance B.) 100 = administrative distance, 1300 = hop count C.) 100 = administrative distance, 1300 = metric D.) 100 = hop count, 1300 = metric

1 Answers  


Which command will enable CHAP authentication on a serial interface that is using PPP? A.) encapsulation chap B.) ppp chap C.) ppp enable chap D.) ppp encapsulation chap E.) ppp authentication chap F.) ppp chap enable

2 Answers  


Categories