What is the diffrence in between Class PS & Class 5P10 for CTs

Categories >> Engineering >> Electrical Engineering
Suggest New Category

What is the diffrence in between Class PS & Class 5P10 for
CTs

Question Posted / indermani

7 Answers
11079 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / subharaj

PS Class CTs are used for Differential protection & 5P10
are used for other protection.

Is This Answer Correct ?

18 Yes

0 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / k. sankaraiah

calss 5p10 used for normal protection, but PS class used
for special protection. 5p10 is used for non balance
circuits but PS class used for balance circuit.where ever
circulating current is balanced at that time only Ps class
using.This can be used only two CTs are present. Ex.
Differential protection & REF.

Is This Answer Correct ?

1 Yes

1 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / k.prakashchandra

5P10 ct belongs to PS ct group,being specified

Is This Answer Correct ?

0 Yes

0 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / jonnalagadda chowdary

PS Class CTs are used for Differential,over current
protection(direct protection) & 5P10 are used for restricted
earth fault(indirect protection)

Is This Answer Correct ?

0 Yes

1 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / fikizolo

Theres basicly no difference, they both overcurrent protection CT's

Is This Answer Correct ?

0 Yes

2 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / chirag

class ps ct's are special class ct's which are used in
protection where high accuracy is required other than that
5p10 are used.accuracy of 5p10 is less than class ps ct's.

Is This Answer Correct ?

2 Yes

7 No

What is the diffrence in between Class PS & Class 5P10 for CTs..

Answer / satya dev

Class PS CTs are used for Metering system & Class 5P10 used
for Protection

Is This Answer Correct ?

1 Yes

19 No

Post New Answer

More Electrical Engineering Interview Questions

If we have 11 kv RYB Phase single core cable near about. Then wht effect and losses

0 Answers Kirloskar,

Why lightning arrester blast in rainy day?

1 Answers Eco Cement, Mahaveer, MBDL,

what is the mager value of star motor and delta motor between phase to ground and phase to phase, and minimum how much should be value ?

1 Answers

hai now i am working as a electrical design engineer in construction field can i get a job in oil and gass field or power plant project as a electrical design engineer?

0 Answers

Why transformer used in UPS??

0 Answers JLL,

How to calculate Temp from Resister from PT100 equation,

0 Answers

We use ungrounded DC system (220V/110V) for control and protection system in substations etc. Suppose we have long 2 core DC cables running from our DCDB in control room to the load (length of around 2 to 3 km). Do we need to protect these long DC cables from earth leakages or not? If yes how?

5 Answers Siemens,

Hi, We have have the major losses between BBT ( Bus Bar Trunking) to LT Incomer & LT to HT incomer, how to arrive the losses?

1 Answers

what is RR number Abbreviation energy meter

2 Answers Trimax,

what is the difference between contactors & relay.

2 Answers

What is the meaning of C1, C61, C91 cable

0 Answers

why are installed water leakage detection system data centers & server rooms

0 Answers Reliance,

For more Electrical Engineering Interview Questions Click Here