How to calculate meter constant in HT yard pls give me
example for this issue



How to calculate meter constant in HT yard pls give me example for this issue ..

Answer / mohamed ali.m

Hi,

This is Formula ,

PT ratiox CT ration X dial Constant/ Meter PT raioxCT ratio

example ,

100x60x1/1x1 = 6000

example
Final Reading Kwh - 2342.4 , Intial reading Kwh - 2339.5
so Consum 2.9x 6000 = 17400 units Consumed

good Question

Is This Answer Correct ?    9 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

I am gokul. i finished B.E(EEE). I have 2 years experience in maintenance. But now i have not job, so i am searching. i want any effective courses in Electrical field with related to job and good salary. any one will help to me. please tell?

3 Answers  


what is the reasons for blowing fuse

1 Answers  


We are preparing another project which involves Waste heat recovery from a 1 MW GE Engine. The Engine in particular gives out flue gas at 487Deg C with a flow rate of 5650 kg/hour and this can be cooled to 180 Deg C. This gives a thermal output of ~ 594 KW that is available for input to VAM via heat exchanger / boiler. Additionally 581 KW will be available from engine jacket water (temperature profile 80/ 80 Deg C and a flow rate of 50m3/hr) Our estimation is that 300 TR of cooling is possible with a suitable VAM machine(s). Please advise what is the most suitable arrangement with maximum TR and min Capital expenditure. plz reply me as early as possible

0 Answers  


if two transformers are placed parallel & both have fault impedance of 50KA will it increase or decrease show example?

0 Answers  


What should be the magnetic balance test values for a 3 phase delta/star connected single primary dual secondary winding transformer (90 MVA / 2 X 45 MVA TRANSFORMER)

0 Answers  






What determines the thickness of the lamination or stamping?

0 Answers  


Explain the grounding concept adapted in aircrafts?

2 Answers  


How many safety of Disel Generator

5 Answers   Sail,


Which phase is prefered for connecting 1phase vt used for synchronism in an OHL? why?

1 Answers   Siemens,


After taking shutdown of 11kv feeder, if you see 5kv by phasing stick in the cable side, is it possible to close earth switch in cable.

0 Answers   KSEB, L&T, Siemens,


Why indicate only 440V to 3-phase supply.

4 Answers  


1) What are your personal strength? 2) What are your personal areas of improvement? 3) What are your expectations from from a particular job? 4) what are your carrier objectives?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)