how can calculate how much steam is to be required for generation of 1MW elec

Categories >> Engineering >> Mechanical Engineering
Suggest New Category

how can calculate how much steam is to be required for
generation of 1MW electricty?

Question Posted / pintu9774689249

8 Answers
46464 Views
NTPC, SVRI, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / shwan osman

it's calculate by this equation(p=m(h2-h1))
h= enthlpy
m=mass
p=power

p=1MW
m=?
h2=calculate by temp.& pressure steam enter turbine
h1=calculate by temp.& pressure steam exit turbine

Is This Answer Correct ?

58 Yes

8 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / laxmi prasad

3 to 4 ton steam is to be required for
generation of 1MW electricty

Is This Answer Correct ?

40 Yes

12 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / magesh

Simple guys
to produce 1 MW of electricity 4.2 tonnes per hour of steam
is required.

Is This Answer Correct ?

25 Yes

14 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / abhishek giri

steam rate=power generated in turbine/(change in specific
enthalpy of steam while leaving turbine);
henc,steamrequired=(steam rate * time)

Is This Answer Correct ?

7 Yes

0 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / luis

That is just an approximation. It depends on the enthalpy
of the steam, i.e. pressure of the steam and the degree of
superheat and/or reheat added. A ton/hour of steam at 900
psig and 375C will generate less MW than the same ton/hour
at 2850 psig and 590C. Also depends on the generator
efficiency which is generally assumed to be 80-85%.

Is This Answer Correct ?

5 Yes

1 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / supa

Specific steam consumption=design flow/design power

Is This Answer Correct ?

8 Yes

5 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / chaitanya pithawa

no it is theoritical method,
but in real case, we should check the turbine by varying the
speed of the steam and angle of the nozzle,so 1 MW power is
to be generated,at that time we can check the steam velocity
and from that we can calculate the volume of the steam.

Is This Answer Correct ?

9 Yes

7 No

how can calculate how much steam is to be required for generation of 1MW electricty?..

Answer / tejeswararao

That is depend up on turbine design if it is seimens turbine 3.8 tons more than enough if it is triveni turbine it may 4.5tons like that and it may vary as per load curve

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Mechanical Engineering Interview Questions

what is the difference between type -a and type -b iron > The chemical compostion is given here under and also guide us the effect of Ni;Cr;Mo in the iron; name and use of these two types of iron Type a Type b %C :3.15 2.65 %Mn:0.41 0.52 %Si:1.72 1.60 %S :0.090 0.082 %P: 0.215 0.204 %Ni: 0.40 Traces %Cr : 0.49 Traces %Mo : Traces Traces

0 Answers

why we use kg/cm2 in pressure gauge not kg/m2

0 Answers

In terms of electrical enhineering, give a detailed explanation of the "earth fault loop path"

0 Answers National Engineering Industries, NTPC,

plz anyone provide me the sample test papers of ONGC as of i m from Mechanical engg bakground and would be appearing for the test in the june 2010. My email id - neeraj_94312@rediffmail.com

0 Answers TATA,

why it is difficult to make heavy cuts if a form turning tool is complex in shape?

0 Answers

What are the advantages and disadvantages of gear drives over belt drives?

0 Answers

how will u design a pipe?

11 Answers EICS, Greeva, IGCAR,

What is the spinning jenny?

0 Answers

What type of pump is lubricator pump?

0 Answers RRB,

why companies are using First and third angle projection? why not second and Fourth?