Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual
1 3946Identify the command that disables name-to-address translation? A.) Router(config-dns)# no ip domain-lookup B.) Router(config)# no address translation C.) Router(config)# no ip domain-lookup D.) Router(config)# ip domain-lookup
1 4162What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface
1 5714Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
1 4389Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
1 4304Identify the effect of Ctrl-Z? A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the ping operation D.) Exits privileged exec mode
3 6013Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share
2 5125Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
3 6457Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1
2 5170Identify the command to view the configuration-register value? A.) show register B.) display config-register C.) show config D.) show version
1 4923Identify the 2 commands that save the running-config to a TFTP server? A.) write running tftp B.) copy running network C.) copy running tftp D.) write network
3 5331Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode
2 5321How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Rotuer(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run
1 4331What command can be used to test IPX connectivity? A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx ping 2e.0000.0045.8923
4 11585Identify the 2 commands that display the clock rate configured on the serial0 interface? A.) show serial0 B.) show interface serial0 C.) show clock rate serial 0 D.) show controllers serial 0 E.) show running-config
5 9780
Can you explain VPN tunneled packet in detail?
When we use loop back ip?
Which command we use for ping in ipv6?
Define autonomous system (as)?
Explain what is the default behavior of access-list?
Brielfly explain the conversion steps in data encapsulation
Suppose a Switch interface went in error-dis mode what you will do for Troubleshooting List all Possibilities
In which ios version 182 people can access router through telenet?
What is the different between console port and auxiliary port?
What is poe (power over ethernet)?
Does a bridge divide a network into smaller segments?
What is the difference between static and dynamic ip addressing?
Why subnetting is used?
Referring to the commands shown, what command must next be used on the branch router prior to traffic being sent to the router router?
When ospf protocol advertise its routing table?
