Interested to Buy Any Domain ? << Click Here >> for more details...
Station A is transmitting data to station B faster that station B can handle it. When station B's buffer fills up, it send out a message to station A to stop sending data. After B empties out its buffer, station B sends a message to station A to start sending data again. This is most directly an example of (pick the best answer only): A.) Poison Reverse B.) Connectionless protocol C.) Windowing D.) Connection oriented protocol E.) Flow Control F.) Split Horizon
1 5939The Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) provides which of the following? A.) 1.544 Mbps B.) 23B + 1D Channel C.) 24B + 1D Channel D.) 2B + 1D Channel E.) 23B + the Disney Channel
2 4893Which layer manages protocol access to the Network layer? A.) Datalink - MAC Sublayer B.) Datalink - LLC Sublayer C.) Transport D.) Session E.) Network
3 6509Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route
1 5231Identify the command to display all the valid commands at the given mode? A.) Help all B.) Help C.) All commands D.) ?
3 5406Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End
1 8763Identify the command to display the IP host table? A.) show ip hostnames B.) show ip names C.) show hosts D.) show ip hosts
1 6073Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols
2 6074Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0
2 5596Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload
1 6562Identify command that configures 'Cisco1' as a secret password? A.) Router(config)# enable secret password Cisco1 B.) Router(config)# enable secret cisco1 C.) Router(config)# enable password Cisco1 D.) Router(config)# enable secret Cisco1
2 6467Identify the statement which connects access-list 101 inbound to interface e0? A.) Router(config-if)# ip access-group 101 in B.) Router(config-if)# ip access-group 101 C.) Router(config)# ip access-group 101 e0 in D.) Router(config)# ip access-group 101 e0 in
1 4350Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1
3 7000Identify the command that saves the configuration stored in RAM to NVRAM? A.) copy running-config startup-config B.) copy tftp running-config C.) copy startup running D.) copy active to backup
1 4610Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table
1 4637
Which type of updates eigrp protocol do?
Which way of communication bus topology use?
2500 Value in which type of access list?
How do you depict an IP address?
Explain the difference between static and dynamic routing?
What are the different types of passwords that you can use in cisco routers?
Can you describe the Authentication Header (AH) Protocol?
What is the purpose of data link layer?
Explain how many broadcast domains are in switch?
Hi Friend. i have to let you know that now i have been selected for cisco india in bangalore. i am thanking to all of you guys that u have been posted such good question and the respective answer. from today i will be not able to visit this site on regular basic and hopeing that you will continue to post the question.the question you are posting is not very usefull to you but also usefull to another. i am again thanking to all of you and hope for best for your feature. Jitendera kumar sinha Network engineer-L2 cisco india Bangalore
Value in which type of access list?
What is the difference between the communication and transmission?
Can you explain the basic of encryption in VPN?
What is the minimum and maximum request timer?
Referring to the commands shown, what command must next be used on the branch router prior to traffic being sent to the router router?
