Which layer manages protocol access to the Network layer?
A.) Datalink - MAC Sublayer
B.) Datalink - LLC Sublayer
C.) Transport
D.) Session
E.) Network
- 3 Answers
- 5779 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / zibrayal.s.mulla
E) network ,
because the situation among the n/w .those answers can be
helpful in data transmission protocol ....
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / guest
Answer: B
Having two Datalink sublayers provides physical media
independence.
The MAC sublayer encapsulates to the Physical Layer.
The LLC sublayer encapsulates to the Network Layer.
| Is This Answer Correct ? | 0 Yes | 1 No |
You are a system administrator on a NetWare network, you are running NetWare 4.11 and you cannot communicate with your router. What is the likely problem? A. NetWare 4.11 defaults to 802.2 encapsulation. B. NetWare 4.11 defaults to 802.3 encapsulation C. Cisco routers only work with NetWare 3.11. D. NetWare 3.11 defaults to 802.2 encapsulation.
Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.
Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols
What is masking? why is needed?
hi friends i donot know this is the networking question or not but if you help me then i will thankfull to you the problem is like that in my comnay there are 200 user which log one at a time now only one user is not able to get the dhcp address and othr are geting the dhcp my company sys admin is saying that this is the n/w fault while i am saying that this is not the n/w fault for the cleaerfication of my side i take a straight workng cable and connect that user directly to my cisco 24port switch now problem is stiil like that but one thing i wan to say he is geting manually ip and able to access internet he is able to ping the server but whrnever he tyeme \\<ip address of server> error comes like networl path provided not accepted by provider some thing like that. my systm admin is saying that i have o do somthing on my firewall but i am saying that no issue with firewall in that i connect my latop to the spefic port from where the user is conected then i am geting dhcp ip address and i am able to connect the server also i donot know why this is happen my syadmin is senior to me so i canot blame him plz help e what to do i am very weak in the filed of systym jitendera kumar sinha
Why we use filter option?
What is BGP Synchronization rules?? Can any one explain..???
Identify the 2 commands that display the clock rate configured on the serial0 interface? A.) show serial0 B.) show interface serial0 C.) show clock rate serial 0 D.) show controllers serial 0 E.) show running-config
What is SIA (Stuck in Active) in EIGRP?
7 Answers Cap Gemini, Hathway, Reliance Jio,
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
Why OSPF uses 2 Multicast IP
What is the difference between csma/ca?
CCNA 
