If fire would be inside the plant which fire detector is to detected the fire.

KOC,

Dear all,recently in our plant we installed a conveyor for this the motor ratings are 5 hp and Amps 7.39.Due to on urgent starting of conveyor we fix the DOL starter with range of 9-15 amps.give me suggestion regarding on this issue

In an existing power plant (phase I) with step up transformers (3nos) with Ynd1 vector group to the 400KV bus bar,an extension power plant (phase II) with transformers (4nos) with Ynd11 vector group >. what are the consequences of such configuration ,please note that % impedance are also differ i.e. 15% & 10.5% the reason was that auxiliary supply interface is at different voltage levels i.e 400v & 6.6KV in phase i and phase II respectively .please advise ! Thank you !

UNIT OPERATION - EXAMPLE 9.1 : Which of the sequence below represent a feasible flows of ethanol processing plants using cellulose as starting material? A. raw material -> heat exchanger -> distillation column -> reactor. B. reactor -> distillation column -> raw material -> heat exchanger. C. heat exchanger -> raw material -> distillation column -> reactor. D. raw material -> heat exchanger -> reactor -> distillation column. E. distillation column -> raw material -> reactor -> heat exchanger.

units for vibration in power plant

if i added hypo before DM plant so i will affect my resins of anion or cation. if affect it so do prevent what kind of step should be taken to remove hypo before DM inlet?

Hindustan Unilever Limited,

Dear guys we adding hypo at climax plant and that water is inlet to DM plant so with hypo water that can affect my resins of cation and anion. if it is affect life of my anion and cation so what kind of steps should be take.

Hindustan Unilever Limited,

Special Procurement type 40 – proc. form alt. plant

What parameters you maintain in “plant parameters” in configuration?

PROCESS DESIGN - EXAMPLE 21.3 : According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

ENVIRONMENTAL ENGINEERING - QUESTION 22.3 : A well delivers 225 US-gallons per minute of water to a chemical plant during normal system operation. (a) Calculate its flowrate in the unit of mega US-gallon per day or MGD. (b) The following formula is written next to the chlorine feed point : (chlorine feed rate, lb / day) = (flowrate, MGD) X (dose, mg / L) x (8.34). If this formula is correct, then what should the chlorine feed rate to be in pounds per day (lb / day) if the desired dose is 2 mg / L. (c) Prove by calculations that the constant 8.34 in the formula next to the chlorine feed point is correct. Let 1 US-gallon = 3.78541 L and 1 mg = 0.0000022046 pound.

NATURAL GAS ENGINEERING - QUESTION 26.2 : (a) The Hyperion sewage plant in Los Angeles burns 8 million cubic feet of natural gas per day to generate power in United States of America. If 1 metre = 3.28084 feet, then how many cubic metres of such gas is burnt per hour? (b) A reservoir of natural gas produces 50 mole % methane and 50 mole % ethane. At zero degree Celsius and one atmosphere, the density of methane gas is 0.716 g / L and the density of ethane gas is 1.3562 mg / (cubic cm). The molar mass of methane is 16.04 g / mol and molar mass of ethane is 30.07 g / mol. (i) Find the mass % of methane and ethane in the natural gas. (ii) Find the average density of the natural gas mixture in the reservoir at zero degree Celsius and one atmosphere, by assuming that the gases are ideal where final volume of the gas mixture is the sum of volume of the individual gases at constant temperature and pressure. (iii) Find the average density of the natural gas mixture in the reservoir at zero degree Celsius and one atmosphere, by assuming that the final mass of the gas mixture is the sum of mass of the individual gases. Assume the gases are ideal where mole % = volume % at constant pressure and temperature.

NATURAL GAS ENGINEERING - QUESTION 26.3 : The United States of America Energy Information Administration reports the following emissions in million metric tons of carbon dioxide in the world for year 2012 : Natural gas : 6799, petroleum : 11695, coal : 13787. Coal-fired electric power generation emits around 2000 pounds of carbon dioxide for every megawatt hour generated, which is almost double the carbon dioxide released by a natural gas-fired electric plant per megawatt hour generated. If 1 metric ton = 1000 kg and 1 pound = 0.4536 kg, estimate the total energy generated by natural gas in the world for year 2012, in gigawatt hour.

why SCR use in power plant

Edison,

QUANTUM BIOLOGY - EXAMPLE 33.2 : (a) In a biomolecule, ATP hydrolysis will produce 3 kcal / mol to 60 kcal / mol of energy, according to energy scale. Find the range of such energy generation if 2 moles of molecules involved. (b) A formula is given by ln P = ln a + b ln W where P = metabolic rate, W = body size, a = dependent of taxa, b = scaling exponent. If b is approximately 1 for plant, and b is approximately 0.75 for animal, find the relationship of P as a function of a and W in plant.