Answer / kapil asdhir

Thnx Jitendera. Can u give me ur mail id, my yahoo mail & messenger id is asdhir.kapil@yahoo.com. Myself kapil and working in Pioneers Group as a Server Admin. Thnx again Brother

Answer / kapilasdhir

What is FECN {Forward Explicit Congestion Notification}?

Answer / jitendera sinha

What is FECN {Forward Explicit Congestion Notification)
hi kapilashdhir
thanks for the question here is the i am trying to provide answer

fecn=this is a mechanism of frame really congestion control

as we know that in the frame realy mechanism we have some link of limted bandwidth
but if another link is available then we can use that link for our data forwarding.

suppose we are forwarding some data through farme realy network moere then our COMMTED RATE.NOW suddnly some link not avlable but we are not aware of that is there is congesstin in network we are continusly forwarding the data at the same rate.
what happen due to this a trafic congusstion will ocur
so for solving that problem two mechnaism come in acount
1 bemcn-bacward explict
2 fecn-forward explict

i hope it will help to understand the farme really technolgy

now how the both are working
i will explain it latter

Answer / pachicoo

FECN=Forward Explicit Congestion Notification bit

Explicit congestion notification is proposed as the
congestion avoidance policy. It tries to keep the network
operating at its desired equilibrium point so that a
certain Quality of Service (QOS) for the network can be
met. To do so, special congestion control bits have been
incorporated into the address field of the frame relay:
FECN and BECN. The basic idea is to avoid data accumulation
inside the network. FECN means Forward Explicit Congestion
Notification. The FECN bit can be set to 1 to indicate that
congestion was experienced in the direction of the frame
transmission, so it informs the destination that congestion
has occurred. BECN means Backwards Explicit Congestion
Notification. The BECN bit can be set to 1 to indicate that
congestion was experienced in the network in the direction
opposite of the frame transmission, so it informs the
sender that congestion has occurred.

What is the difference between full duplex and half duplex?

0 Answers  

---

Which command loads a new version of the Cisco IOS into a router? A. copy flash ftp B. copy ftp flash C. copy flash tftp D. copy tftp flash

2 Answers  

---

Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# access-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log

2 Answers  

---

What is the main advantage of using switches?

0 Answers  

---

What is a backoff on an 802.3 networks A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. it is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged.

3 Answers  

---

---

To monitor IP igrp traffic, you can use "debug IP igrp transaction" or "debug IP igrp events". How do you display information about IPX routing update packets? A. debug routing B. debug ipx transaction C. debug ipx routing activity D. debug ipx events

2 Answers  

---

What is the size of IP address?

0 Answers  

---

Mention what is the difference between the switch, hub, and router?

0 Answers  

---

Which layer defines the physical topology? A.) Application B.) Transport C.) Network D.) Data Link E.) Physical F.) Session

1 Answers  

---

Difference between routed and routing protocols not difference between protocol between those.

3 Answers   HCL, TCS,

---

Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup

1 Answers   Karrox,

---

What does aaa stands for?

0 Answers  

---