Answer / kashish kalra

potential differnce is basically the the differnce between
the two points,
voltage drop is the amount of voltage spend to overcome
the impedance offered by any pasive components in an
electric circuit,
whereas emf is electromotive force ..which not actually a
force rather an amount of volatge which tends to flow a
certain amount of current in the circuit.

Answer / percy

VOLTAGEDROP AND POTENTIAL DIFFERENCE ARE SAME

BOTH R ACTUALLY THE DIFFERENCE IN POTENTIAL AT TWO POINTS

EMF OF POTENTIAL IS DEFINED AS THE FORCE REQUIRED TO BRING
UNIT "+'VE CHARGE FROM INFINITY TO A GIVEN POINT.

Answer / amolkarne

EMF : VOltage acrooss the source teminal when load is not
connected (Unit:Volt)

Voltage Drop: Drop in voltage due to current & resistance
(or impedence)in the circuit is nothing but Viltage Drop
(unit:Volt)

P.D.: Diff.in the potential (or voltage)of the two terminals
in the circuit is nothing but P.D

Answer / rahul babu

potential difference is basically difference in charge b/w
two points.as a positive test charge is bring from infinity
to a given point.
while voltage drop is amont of current dissipated by an
impedance or resistace

and emf is voltage generated in case of magnetic field..

what is the relation between the leading pf and supply voltage?

1 Answers  

---

How to calculate amount of copper used in a motor (AC&DC), generator and transformer? Datasheet provides power rating and mass of the equipment....can we somehow use this available info.

1 Answers  

---

why using transformer and thyristor switch in 3 phase apfc panel

0 Answers   Reliance,

---

how to make parrallal ups

1 Answers  

---

How to design a Unit auxiliary transformer for a power house having a unit of 65 MW and Generating voltage of 11 KV and Secondary voltage of 433V

0 Answers  

---

TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2

0 Answers   KSEB,

---

What will be done if we open the secondary of CT on load??

4 Answers   Engro,

---

A 40 kva transformer has a core loss of 400W and a full load copper loss of 800W. What is The proportion of full load at maxmimum efficiency?

1 Answers  

---

when meggering a 3ph,480v oil reservoir heater on a regen gas compressor, why do I get a reading to ground when meggering phase to ground? shouldn't it read opened or is there something that makes it read closed? on the same heater, when ohming, it reads open. thanx

1 Answers  

---

What is the minimum value required for Neutral to Earth in UPS Panels

3 Answers  

---

TCS IS IT COMPANY THEN WHY DO THEY NEED ELECTRICAL &ELECTRONICS ENGINEERS?

0 Answers  

---

why the India electrical supply transmission loss is high when compare to us

0 Answers  

---