For 300 MW plant what is the distribution voltage

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / muralichppl

6 Answers
10089 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

For 300 MW plant what is the distribution voltage..

Answer / santosh

Its 220 KV no doubt.

Is This Answer Correct ?

4 Yes

1 No

For 300 MW plant what is the distribution voltage..

Answer / virendra joshi

It depends that receiving station is how far & also how
many feeders are to be taken. if power is 300 MW then HV
transmission is ideal because the conductor size would be
less & hence the cost of transmission is less. if i would
be the designer i use 400 KV 2 nos feeder to receiving
station.

Is This Answer Correct ?

1 Yes

0 No

For 300 MW plant what is the distribution voltage..

Answer / joel

The distribution voltage is the LV that you will get. Like
for example in a 300MW 138kV/13.8kV substation, 13.8kV line
will go to the building RMU then this will be step down to
380V for distribution by a distribution transformer
installed in the building.

Is This Answer Correct ?

1 Yes

0 No

For 300 MW plant what is the distribution voltage..

Answer / jagannath swami

Its fully depend upon the switch yard (EB ) how much distance from ur end as per ER 300 MW power gen. upto 220kv S.S. is required . and the distribution is ur hand

Is This Answer Correct ?

0 Yes

0 No

For 300 MW plant what is the distribution voltage..

Answer / ranjan

it is 6.6 kv .

Is This Answer Correct ?

2 Yes

3 No

For 300 MW plant what is the distribution voltage..

Answer / khader shah

Distribution voltage will be 380 to 460 volts only for a 300
MW plant

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

How shall i design a liquid rotor starter

0 Answers

Iwould like to know barc interview questions

0 Answers BARC,

why nearly all voltages are in the multiples of 11?

5 Answers

Please help me regarding my one concern. - During earth pit testing we noticed that the Clean earth pit and dirty earth pit showing continuity (Resistance value - 5ohm) . I want to know that if both earth pit have separate location and there is not internal looping between PIT then why such continuity is showing on it . Because of this issue the field side all earthing point showing short. In PLC panel we are providing two types of earthing cable which is coming from separate earth pit (Clean and Dirty earth pit) because of earth PIT showing short our PLC is not complying spec . please help regarding this issues.

0 Answers

please tell 1 ton equal to how many kilo watt?? in some converter software's that is 3.5 kw. is it right?

8 Answers Mitsubishi,

we all know voltage is a force(emf), and the force always devides if 2 or more than2 loads are there but why does the voltage remains same is parallel, it must devide na ???

0 Answers NTPC,

What happens when the field of an alternator connected to infinite bus is suddenly removed?

3 Answers

how many earthing required for ups, what should be the earth voltages

9 Answers Juniper Networks,

where induction generator is used ?

1 Answers

what is transformer tap change HT side and LT side

1 Answers Alstom, Sodexo,

HOW CAN YOU CALCULATE PRACTICAL EFFICIENCY OF A ASYNCHRONOUS INDUCTIONMOTOR OF 7.5KW,& MOTOR IS RUNNING WITH AVOLTAGE OF 410 VOLTS,& TAKING CURENT OF 13 AMPS

0 Answers

How can we calculate the transformer rating if the load calculated is 1000KW (11Kv Supply)?

0 Answers

For more Electrical Engineering Interview Questions Click Here