Answer / vijay chander

first we informed to respective electricity office and then
find the fault inside the VCB or E.B side. if inside the
VCB means call the person from VCB manufetures.

Answer / sskumar

Hai everybody,

Good and thanks to all of you for giving a ideas.But here
we should discuss only Technical matters not for
management.
So coming to the point, first we should cut off the
incoming supply to the VCB, how? first we should open the
AB switch, then automatically the supply wont come to VCB.
Then remove the VCB and rectify it.

Answer / gunasekaran

if we have double bus system we can close the B/C unit and
get the supply from another bus

Answer / kanand078

if DG is there run the pland at dg load..after i will check
the fault and rectify

Answer / y.hari kishore babu

first we should cut off the incoming supply to the VCB, how?
first we should open the AB switch, then automatically the
supply wont come to VCB.

Then remove the VCB and rectify the problem by vendor or
myself with help of our tecnicians

Answer / g.kumaresan.

If Main incomer fail in our site Immediatly to Isolate the
incomming supply and VCB. Bec's to protect the inside Heavy
Equipment insite in our site, then to inform the situation
in our Authoriy officer, at the same time to ensure the
back feeding arrangement, Bec's can not maintain the supply
intruption in long time.

So, doing back feeding arrangement immediatly with our
higher authrity knowledge and also other officer sugection.

Answer / anish salvi

If the incomer is further joint to transmission line Than no worry!! just Bypass the CB beacuse there are always CTs & pTS for the measurement purpose & in case if any fault occurs than even in absense of the Vaccum circuit breaker (used for 110KV and above)

Where as if it is the Distribution than use DO fuse for protection 

Hi Suppose we have a wye/wye transformer which is grounded at both sides,in this situation, do we have ay ground transformer? in other words, ground transformer can do any thing more (while we have nuetral wire in both sides)? As the last question, what about 3rd harmonic? we have two choices: first using wye/delta transformer + ground transformer and second using wye/wye earthed connection.in the former choice, we dont have 3rd harmoonic at the secondary side but what about Yn/yn conection? do we suffer from 3rd harmonic in the Yn/yn connection?

0 Answers  

why power of fm is weaker than am?

1 Answers  

why ss stablity limit is more transient stablity limit?

0 Answers   IOCL,

WE ARE PLACE A NEW 75 KW MOTOR FOR JPF.IT IS CONNECTED IN M.C.C. WHEN WE ARE STARTING M.C.C.INCOMER IS TRIPPED.THEN WE ARE CONNECTED IN P.C.C WITH A MM30 RELAY PROTECTION THEN WE ARE STARTED MOTOR WILL RUN SMOOTHLY.

0 Answers  

whats the advandage of PMG in alternator?

2 Answers  

simple way to find busbar sizes??

1 Answers   SPAC,

Why is transformer a machine

1 Answers   Grasim,

Hi,iam a diploma in electrical engineering.rtd from indian air force in apr 2007.prsently working in reliance next link as a network maintenance engineer since 2007,can i get a job in motherson sumi.

0 Answers   Motherson, Motherson Molds and Diecasting Ltd.,

what type of questions are asked and howmwny questions belong this catagory?

0 Answers   RRB,

Why in power plant projects we see DOL starting method used for motors upto 160 kW instead of star delta method

0 Answers   UCC,

using in R,Y& B PHASE LTSIDE(415V)ct ratio 4000/5 WITH ENERGYMETR OF 1280 REV./KWH,240V.WHAT WILL BE MF OF METRE.

1 Answers   HCC,

what is looping circuit in electrical lighting circuits?

5 Answers   L&T,