Answer / karthik raman.b

its depend on current of the load which connected to the battery amphere per hour if a battery having 10AH it can give 10A load upto a hour

Answer / krish

it depond upon the output load

Answer / avinash

First you must know the ampere-hour of your battery bank as
per the manufacture's specification.Now discharge the
batteries as per the C5 rating( for Ni-Cd batteries) or C10
rating (for Lead -acid Batteries).Discharging can be done
by connecting the positive and negative terminals of
batteries to the copper plates and immersing in a salt
solution, which will act as a load. The distance between
the plates can be adjusted to set the discharge current.
Measure the amount of discharge current and time till the
battery voltage of each battery in a bank drops to 1 Volt
if it is a 1.4 volt cell. Now multiply the discharge
current and time. This is the measure of the Amperehour
capacity of the bank.If the Amppere -hour capacity as per
the manufacture is available then you can determine the
percentage capacity of your bank at present.Remember that
charging and discharging of battery bank improves the
health of the battery bank.However, for lead -acid
batteries these cycles are around 750 or say 3 years. For
Ni-Cd batteries the life is around 25years or more if
maintained properly.Selecting a overated battery is also
not adviseable as it won't get discharged completely and
this may result in sulfation of batteries and early death
of battery bank.

Answer / sanat ullah khan

Answer
# 1 it depond upon the output load

Thanks for Marking this Answer 0 Krish
Answer
# 2 its depend on current of the load which connected to
the battery amphere per hour if a battery having 10AH it
can give 10A load upto a hour

Thanks for Marking this Answer 0 Karthik Raman.b
Answer
# 3 Hi Krishna,

V HV AN 65AH 32 No's of Batteries connected 60kva UPS,

What will be the full load backup time???

Thanks for Marking this Answer
Answer
# 4 First you must know the ampere-hour of your battery
bank as
per the manufacture's specification.Now discharge the
batteries as per the C5 rating( for Ni-Cd batteries) or C10
rating (for Lead -acid Batteries).Discharging can be done
by connecting the positive and negative terminals of
batteries to the copper plates and immersing in a salt
solution, which will act as a load. The distance between
the plates can be adjusted to set the discharge current.
Measure the amount of discharge current and time till the
battery voltage of each battery in a bank drops to 1 Volt
if it is a 1.4 volt cell. Now multiply the discharge
current and time. This is the measure of the Amperehour
capacity of the bank.If the Amppere -hour capacity as per
the manufacture is available then you can determine the
percentage capacity of your bank at present.Remember that
charging and discharging of battery bank improves the
health of the battery bank.However, for lead -acid
batteries these cycles are around 750 or say 3 years. For
Ni-Cd batteries the life is around 25years or more if
maintained properly.Selecting a overated battery is also
not adviseable as it won't get discharged completely and
this may result in sulfation of batteries and early death
of battery bank.

Thanks for Marking this Answer 0 Avinash

Answer / mahesh meshram

Calculate the AH of battery as said above or the given by the manufacturer if is same then ok if not then take actual calculated. If capacity of battery is 10AH and load current is of 10A then it will give back up for 1H

Answer / thowsif_emerson_csm team

Hi Krishna,

V HV AN 65AH 32 No's of Batteries connected 60kva UPS,

What will be the full load backup time???

What happen if we apply square wave or traiangular waveform voltage to the transformer primary winding instead of sinusoidal wave?

0 Answers  

what is the lemen of a single 5mm 13000mcd white led pls reply

1 Answers   Eskom, Sona,

how to reduce the magnetizing current in distribution transformers

1 Answers  

Why using synchronising methed in DG's sets?

0 Answers   Juniper Networks,

from which formula we select a capacitor rating?

0 Answers   CLG,

For 415v,3phase,22kw rating of motor how to calculate MCCB rating

2 Answers   Zigma Technologies,

what is ring main unit?

1 Answers   Otis,

what is overflexing in transformer? setting?

1 Answers  

what are the differences between 'exhaust fan', 'heavy-duty exhaust fan' & 'super heavy duty exhaust fan'. what are their power ratings ?

0 Answers   CG,

Write masons gain formula.

0 Answers  

what are the changes made in induction motor so that it act as induction generator

4 Answers   APPSC,

why does not tester light up when it is touched to neutral of 3 pin socket.

4 Answers