Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


A bearing is designated as 6205 , what is it’s bore
diameter:

Answers were Sorted based on User's Feedback



A bearing is designated as 6205 , what is it’s bore diameter:..

Answer / tulika

i don't understand. please describe?

Is This Answer Correct ?    2 Yes 0 No

A bearing is designated as 6205 , what is it’s bore diameter:..

Answer / ajay

what are the 100 components in hydraulic circuit

Is This Answer Correct ?    2 Yes 0 No

Post New Answer

More Mechanical Engineering Interview Questions

What is acceleration

1 Answers   RRB,


DOES IS 2062 SPECIFIES ONLY SEAMLESS PIPES OR ERW PIPE IS ALSO COVERED UNDER IS 2062

0 Answers  


what is the fuction of asstt. rigman drilling

0 Answers   ONGC,


Is radiography require in IBR piping of size 40 NB(1 1/2" inch)?

0 Answers  


What are the causes of failure of superheater tubes ?

0 Answers  


length l and width b is given for a rectangle.and the perimeter of a rectangle is denoted by p.another rectangle length is 2l and width is 3b and the perimeter of a rectangle is p1.find the ratio between those two perimeters?

1 Answers  


which one of the following loading is considered for the design of axle. 1)bending moment only 2) twisting moment only 3) combined bending moment & torsion 4) combined action of bending moment & axial thrust

2 Answers   APPSC,


After any cause of repaired how i start the engine by slow speed 800 to 900 rpm electronic control moudle engine [cummins]

0 Answers   Cummins,


Enumerate some differences between an "orifice" and a "notch". Also tell if "jet" relates more to an orifice or a notch?

2 Answers   Variant,


What type of pump is commonly used is feed water system in auxiliary boiler?

0 Answers   ABC Inc, RRB, Siemens,


how to start the answer for question : tell me about ur self ?

4 Answers   Satyam,


Identify the parts of propeller

1 Answers   RRB,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)