Answer / jitendera kumar sinha

hi jitendera sinha is here
at firsltly comand for making switch in the client mode
is
switch#vlan database
switch(vlan)#vtp domain abc
switch(vlan)#vtp mode client

this is the comand for making switches in client mode

two connect two diffrent switches camnd are
switch(config)#interface fa0/24(the number of port to which
you are going to connect Another switches)
switch(config-if)switch-port trunk encapsulation dot1q/isl

( isl for deafult cisco switchsc and dot1q is for another
vendor switches)

switch(config-if)#switch-port mode trunk


i am going to write all comand once again
switch(config)#interface fa0/24
switch(config-if)switch-port trunk encapsulation dot1q/isl
switch(config-if)#switch-port mode trunk

these are the comand which for your questions

Answer / kamalpreet singh

First of all, is raw switch is a manageable or
non-manageable if switch is manageable and tht is CISCO
switch then you have to do follow the steps given by
jitender. if it is a non-manageable then you should add a
port in a vlan and provide a subnet of that vlan to that
department

Answer / nawaz

first of check switch is manageable or non mangageabl
if managable the we will make clicent
if non managebale then we add port in an vlan and provide of
than vlan to that network segment.

Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. In order for two ends of virtual circuits to communicate using Frame Relay, their network addresses must be mapped to DLCIs.

2 Answers   Wipro,

---

Station A is transmitting data to station B faster that station B can handle it. When station B's buffer fills up, it send out a message to station A to stop sending data. After B empties out its buffer, station B sends a message to station A to start sending data again. This is most directly an example of (pick the best answer only): A.) Poison Reverse B.) Connectionless protocol C.) Windowing D.) Connection oriented protocol E.) Flow Control F.) Split Horizon

1 Answers  

---

A router on one side of a PPP link uses the resonance RTR1 and the password COPP1-PWD. Which configuration line on RTR1 enables a connection between RTR1 and another router named RTR2? A. username, RTR2 password COPR1-PWD, B. username, RTR1 password COPR1-PWD, C. username, RTR2 password COPR2-PWD, D. username, RTR1 password COPR2-PWD,

1 Answers  

---

Identify the command to configure DLCI 100 on an interface e0? A.) Router(config)# frame-relay local-dlci 100 B.) Router(config)# frame-relay local-dlci 100 int e0 C.) Router(config-if)# frame-relay local-dlci 100 D.) Router(config-if)# frame-relay local-dlci 100 int e0

1 Answers  

---

Which two statements accurately define IP addressing rules? (Choose two) A. IP multicast addresses start with 240 B. A host Carbon of all 1 a indicates a network broadcast C. The value of zero (0) in the host Carbon means all hosts on the network D. IP addresses are four octets long and contain a network Carbon and a host Carbon

2 Answers  

---

What are the two types of access lists that can be configured on a Cisco router? A. Standard B. Extended C. Filtering D. Packet

2 Answers  

---

Which fields of an IP packet provide for fragmentation of datagrams to allow differing MTUs in the internet? A. Identification B. Flags C. Frag Offset D. Type of Service E. Total Length

1 Answers  

---

What is name of ospf algo?

0 Answers  

---

2500 Value in which type of access list?

0 Answers  

---

What is the standard ISDN term for a native ISDN modem? A.) ET B.) LE C.) TE2 D.) TE3 E.) TA

1 Answers  

---

You need to come up with a TCP/IP addressing scheme for your company. Which two factors must you consider when you define the subnet mask for the network? A.) The location of DHCP servers B.) The volume of traffic on each subnet C.) The number of subnets on the network D.) The location of the default gateway E.) The number of host IDs on each subnet

1 Answers  

---

what is firewall how fiarewall work how many interfaeces in the cisco pix 501 firewall what is the working of that dmz interface

3 Answers   Aptron, Volvo,

---