Answer / paritosh shah.

Low and High Tension refers to the Voltage of the system.
Normally 1100 Volts (1.1 KV ) and above voltages are
considered H.T.
Voltages below 1100 Volts - e.g. 415, 660 etc. are
considered L.T.

Answer / sabuj

L.T=low tension
0-1kv

Answer / neeraj chouhan

There are Three Type of Voltage Level.
1.: L.T- LOw Tenstion Line, Which can control by ACB, MCCB
& MCB and it is up to 220V to 1.1Kv.

2.:H.T- High Tenstion Lines, Which also Divide in Two parts
2A.: Medium Voltage, Which can control By OIL CKT breaker,
VCBs, RMU, LBS.etc Its having Range 3.6 Kv to 36Kv.

2B.: High Voltage, Which is contol by SF CKT Breaker(66KV
to 220 Kv)

3.: EHV-Extra High Voltage (400KV, 765KV 1250KV)which can
control by very high engineering Relays and control System.

Answer / benchalli nagaraj

LT:MEANS LOW TENSION ITS RELATED TO VOLTAGE
THERE ARE THREE
1) LOW VOLTAGE (0 TO 415V)
2) MEDIUM VOLTAGE ( 415 TO 690V)
3) HIGH VOLTAGE ( ABOVE 690V,11000 LIKE)

Answer / a.bala

L.T=Low tension
Upto 60 HP to be consider as LT ( 60 hp in Tamilnadu and
80 hp in gujarath )

Answer / aiskandar

LY is Line Trap

Answer / ramya

l.t = low tension
0-200 kw

what is the circutor?why we use it ?

0 Answers  

What is the difference between diode and a transistor in terms of the direction of current flow?

0 Answers  

State and define norton’s theorem?

0 Answers  

choose the non-switch device (A) transformer (B) diode (C) transistor (D) IC

3 Answers  

why ten delta testing is carried out on power transformer

0 Answers  

what is difference b/t ac current and dc current

4 Answers   L&T, Meghana Engineers,

IN 3 phase induction motor where we give i/p supply & how its working ?

2 Answers  

how to change the load sharing between two synchronized identical alternators when both are running with Diesel engine? assume both are feeding to same feeder?

1 Answers   BARC,

for what voltage will reactive power be largest in 380 kv line : a) 375kv b)380kv c)385kv

0 Answers  

please send me privious exam's queation papers of section engineer(electrical).

0 Answers   RRB,

I hv a question regarding power factor improvement just after transformer. I request you to reply me plzz. thank you sir. My friend has a small unit of fabrication. in his factory the main load is a welding machine, lathe machine, grinding machine. this load is not continuous type. now our electricity board has installed 16 KVA, 11000/433 V transformer for our factory. In the energy meter (trivector meter) at LV side of transformer, i hv seen power factor value of 0.15 only when only 3 KW load was flowing. Further electricity board has suggested to install 4 KVAR capacitor at LV side after energy meter. Now my question is that if we permanantly install and switch on 4 KVAR capacitor after energy meter, during some load on transformer and also without any load on transformer, wht will be the power factor shown in energy meter?i dont want to get any penalty by electricity board, so plz suggest me if i can permanantly install and switch on the 4 kvar capacitor or not at LV side of transformer just after energy meter? Thank you again and awaiting for ur positive reply soon.

9 Answers  

what is the use of 6.6kV/6.6kV Transformer???

3 Answers