Answer / maheshmcp

1.VC means Virtual Circuits. It is a logical connection
between routers via frame relay Switch.

2. PVC means Permanent Virtual Circuits. The Circuit is
permanent untill the data transfer exceeds a Certain limit.
for eg 1000 mb 2000mb etc. It is just like a Mobiles
Prepaid card.

3. LMI means Local Management Interface. It is a signaling
standard betweek the Router & Frame Relay Switch.

4. DLSI: IT is not DLSI. It is DLCI: Data Link Connection
Identifier. The pvc's are identified to the DTE end devices
(Router) by Data Link Connection Identifier.

Identify 3 IP routing protocols? A.) RIP B.) AURP C.) OSPF D.) IGRP E.) ARP F.) ICMP

2 Answers  

---

What will you do if ur IOS in coorrupt/deleted/Wrong Type/No IOS image ?

3 Answers   Allied Group,

---

Which multicast ip eigrp protocol use?

0 Answers  

---

You want to enable both arpa and snap encapsulation on one router interface. How do you do this? A. The interface can handle multiple encapsulation types with no extra configuration. B. Assign two network numbers, one for each encapsulation type. C. Enable Novell-ether to run multiple encapsulation types. D. Both arpa and snap are enabled by default so you don't have to configure anything.

2 Answers  

---

Suppose we are having two router i.e. Router1 and Router 2 connected with each other on Serial Link,Router Network having ip 192.168.1.0/24. 1> which ip is used at router1 and router2 interface? 2>Which Command is used to assign ip to router1 and router2 interface?

1 Answers  

---

---

What is VLSM ?

5 Answers   HCL,

---

What does the command "IP name-server 255.255.255.255" accomplish? A. It sets the domain name lookup to be a local broadcast. B. This is an illegal command. C. It disables domain name lookup. D. The command is now defunct and has been replaced by "IP server-name ip any"

1 Answers   Cisco,

---

Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface

1 Answers  

---

You need to come up with a TCP/IP addressing scheme for your company. How many network IDs must you allow for when you define the subnet mask for the network? A.) One for each WAN link B.) One for each router interface C.) One for each NIC installed in each client D.) One for each subnet with hosts E.) One for each host ID

1 Answers  

---

Which of the following is a characteristic of a switch, but not of a repeater? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet

2 Answers  

---

You create the following standard access-list access-list 1 deny 1.1.1.1 access-list 1 deny 2.2.2.2 int e0 ip access-group 1 in Which of the following statements are true, with regard to traffic flowing into E0? A.) This will stop IP packets with a source address of 1.1.1.1 only. B.) This will stop all IP packets. C.) This is an invalid configuration. D.) This will stop no IP packets. E.) This will stop IP packets with a source address of 2.2.2.2 only. F.) This will stop IP packets with a source address of 1.1.1.1 and 2.2.2.2.

1 Answers  

---

Which ISDN protocol prefix specifies switching and signaling? A.) I B.) E C.) Q D.) S

1 Answers  

---