Interested to Buy Any Domain ? << Click Here >> for more details...
What is VLSM? how to Calculate VLSM? where it is use and
why?
- 13 Answers
- 48945 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / pardeep kumar
vlsm is a variable length subnet mask.
it is classless network.
in the classless network,we take a large network and convert into small network using the different subnet mask into a network.
that is called a vlsm.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / avinas kumar
Variable Length Subnet Mask. It is created many subnet
from One network.
2.Improve network performance
3.Avoid waste ip address
4.VLSM calculation depends on No of host using in single
network
5.its is used to reduced the size of routing
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / vaibhav
VLSM (variable length subnet mask) is ipv6 classless ip
addressing. Use to subnet an already subnettted ip adress.
how to calculate vlsm?
first if you have a topology you must determine which
network have the greatest number of host. then assign it as
the first subnet.
ex: ISP wan = 20 Host
IP AD=192.168.1.0
isp wan have a 20 host so its means
20host delta=32 subnet mask=255.255.255.224
ADD THE DELTA=32 IN THE IP ADRESS :
192.168.1.0
+ 32
-----------
192.168.1.32
configuration:
192.168.1.0/27
192.168.1.32 IS THE BROADACST ADRESS.
| Is This Answer Correct ? | 0 Yes | 1 No |
Which IP address and wildcard mask would you use in your ACL to block all the hosts in the subnet 192.168.16.43/28?
Tell me when we use standard access-list?
Which commands would assign and enable IPX on an interface ? A.) enable netware B.) enable novell-ether C.) router#(config)ipx routing D.) You must first enable IPX globally and then assign the network number to the interface . E.) enable ipx F.) router#(config-if)ipx network 4a
what is different between cisco router and layer 3 switch
Which three protocols are correctly matched to their transport layer functions? (Choose three) A. route selection IP B. sliding window UDP C. well known pods IP D. route validation ICMP E. connection oriented TCP F. three-way handshake TCP G. no sequence and acknowledgement UDP
Explain how many types of ends in wan?
what is routing and routed protocol ?
MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Network C.) Datalink D.) Transport E.) Application F.) Presentation
Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!
How would you configure one host name that points to two IP addresses? A. IP host jacob 1.0.0.5 2.0.0.8 B. IP jacob 1.0.0.5 2.0.0.8 C. IP host jacob 1.0.0.5 D. IP host duplicate "all"
Why we used Virtual MAC in GLBP
Which OSI layer handles physical address, network topology? A.) Presentation B.) Physical C.) Transport D.) Application E.) Data-Link F.) Network
CCNA 
