Answer / kapilasdhir

Layer 3 Switch provides the connectivity between two or
more different Network ID. It is basically use for Inter
VLAN Routing in the Network.

1900 Value in which type of access list?

0 Answers  

---

Identify 3 characteristics of IP RIP? A.) Distance vector B.) Administrative distance is 120 C.) Periodic updates every 60 seconds D.) Uses a composite metric E.) Can load balance

1 Answers  

---

What are the possible ways of data exchange in ccna?

0 Answers  

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

. Which command sequence will allow only traffic from network 185.64.0.0 to enter interface s0? A. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-list 25 out B. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-group 25 out C. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-list 25 in D. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-group 25 in

1 Answers  

---

---

Identify the default serial encapsulation? A.) ISDN B.) HDLC C.) SDLC D.) Frame Relay E.) PPP

2 Answers  

---

Which OSI layer establishes, maintains and terminates sessions between hosts? A.) Application B.) Physical C.) Data-Link D.) Presentation E.) Network F.) Session

2 Answers  

---

How does PPTP encapsulate data?

0 Answers   CCIE,

---

intial information of packey occur on which layer application sessions physical mine answer physical

1 Answers  

---

Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config

2 Answers  

---

What does the term Base refer to in 100BaseT A. cabling type B. singnal type C. 100 mode type D. spectrum used E. speed category

3 Answers  

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---