What is the difference bt QA and QC
- 9 Answers
- 13276 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / mumtaz
QA: Its looking at improving the whole developement process
to make it run smoothly and effectively. QA is all about
process.
QC: is to check that certain levels of quality are observe
as a result of the improvement that have been made to the
process. QC is all about product
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / lakshmi
Quality Assurance is Monitoring and measuring the strengths
of a development Process.
Quality Control is Validating the S/w.
QA--------->During process (what precations taken by)
Qc---------> After Process (How you performed atlast)
| Is This Answer Correct ? | 2 Yes | 1 No |
Answer / mercy
QA is a preventive method and QC is a detective method.
QA sets up process, improves process and identifies defects
in process.
QC is concerned with the product the process produces.
QA can be called as control over QC.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / preethi
QA:A planned and systematic set of activities necessary to
provide adequate confidence that requirements are properly
established and products or services conform to specified
requirements.
QC:The process by which product quality is compared with
applicable standards; and the action taken when
nonconformance is detected.
QA:An activity that establishes and evaluates the processes
to produce the products.
QC:An activity which verifies if the product meets
pre-defined standards.
QA:Helps establish processes.
QC:Implements the process.
QA:Sets up measurements programs to evaluate processes.
QC:verifies if specific attribute(s) are in a specific
product or service
QA:Identifies weaknesses in processes and improves them.
QC:Identifies defects for the primary purpose of correcting
defects.
QA is the responsibility of the entire team.
QC is the responsibility of the tester.
Prevents the introduction of issues or defects
Detects, reports and corrects defects
QA evaluates whether or not quality control is working for
the primary purpose of determining whether or not there is a
weakness in the process.
QC evaluates if the application is working for the primary
purpose of determining if there is a flaw / defect in the
functionalities.
QA improves the process that is applied to multiple products
that will ever be produced by a process.
QC improves the development of a specific product or service.
QA personnel should not perform quality control unless doing
it to validate quality control is working.
QC personnel may perform quality assurance tasks if and when
required.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / mamta
QA-It is a process oriented activity
QC-It is a product oriented activity
QC will never interfer with the process ,only modify the
product,whereas QA will tell the employee to modify the
process.
| Is This Answer Correct ? | 2 Yes | 2 No |
1. Quality assuarence is Process orientated and quality
control is product oreinted.
2. Quality assuarence prevents the defects.
Quality control detects the defects.
3. Quality assuarence is line function.
Quality control is staff function.
Murali
dharanmu@yahoo.com
| Is This Answer Correct ? | 1 Yes | 1 No |
QA=> Activities done to ensure that process is good enough to make product inline with requirements,develop and maintain the product effectively in a given span of time.
QC=>Activities done to ensure that product is inline with the requirement.Testing product,detecting the bugs & fixing the bugs come under this category.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / nisha
QA:-1.It is a process oriented.
2.It consist of activities like review & walk through.
3.It is a verification process.
QC:-1.It is a product oriented.
2.It consist of activities like unit,integration,system,
UAT.
3.It is a validation process.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / karunakar reddy
QA Is Process to Prevent The Defects throgh Reviews
Walk Thruoghs,Unit Testing,Integration Testing.
QC Is Process to Correct The Defects Through Black Box
Testing.
| Is This Answer Correct ? | 1 Yes | 2 No |
tell me some gud sites for testing??
what are the defects in gmail
Hi Folks What are the Interview Questions in Manual testing that I should be aware of. pls give some Interview Questions in Manual testing. Thanx in advance Sunitha.
why r u looking for change?what should be answer for this?i faced this question in an interview.suggest be gud answers.
1.What is bidirectional traceability ??? and how it is implemented? 2.What is Automation Test frame work ? 3. Define the components present in test strategy? 4. Define the components present in test plan? 5. Have u written Test plan ?…. thank u!plz reply........
How could you present test strategy for the product testing?
is Business requirment doc is configurations item or not how you control configurations control
testing is a procedure or methodology,diff between methodoly and procedure?
hi.i joined in a software testing course recently.but i dnt knw 'c' or 'c++',would it mind? my stream is ece. so i just had a C&DS IN OUR 1ST SEMESTER.
what is the architecture of your current project?
If the Time is cut shorted, how can you manage that?
exactly what is the purpose of configuration mgt tool? also give some examples?
Automation Testing 
