What are some factors to consider when trying choosing between a dry screw compressor and an oil-flooded screw compressor?

0 Answers  

---

Question 69 - A well delivers 225 US-gallons per minute of water to a chemical plant during normal system operation. (a) Calculate its flowrate in the unit of mega US-gallon per day or MGD. (b) The following formula is written next to the chlorine feed point : (chlorine feed rate, lb / day) = (flowrate, MGD) X (dose, mg / L) x (8.34). If this formula is correct, then what should the chlorine feed rate to be in pounds per day (lb / day) if the desired dose is 2 mg / L. (c) Prove by calculations that the constant 8.34 in the formula next to the chlorine feed point is correct. Let 1 US-gallon = 3.78541 L and 1 mg = 0.0000022046 pound.

1 Answers  

---

What parameters should be considered while selecting type of filter?

4 Answers   Nocil,

---

PROCESS CONTROL - EXAMPLE 6.2 : A stream with volumetric flow rate Q enters a cylindrical tank and a stream with volumetric flow rate q exits the tank. The fluid has a constant heat capacity and density. There is no temperature change or chemical reaction occurring in the tank. Develop a model for determining the height of the tank, h. Let V is the volume, A is the cross sectional area, r is the density, m is the mass, where V and A are for the tank, r and m are for the fluid. The rate of mass of fluid accumulation, dm / dt = (Q - q) r. Prove the model to be dh / dt = (Q - q) / A.

1 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.5 : The following formula is used as a reference : (analyte signal) / (internal standard signal) = (f-factor) x (concentration of analyte) / (concentration of internal standard). A solution containing 3 mM of analyte and 4 mM of internal standard gave peak signals of 2 and 3 mamps respectively. Another similar solution containing 2 mM of analyte and 1 mM of internal standard gave peak signals of 1 and 4 mamps respectively. Find the average f-factor.

1 Answers  

---

---

Why water is not directly added to sulphuric acid for dilution?

8 Answers  

---

Name some common causes of control valve noise?

0 Answers  

---

pleas tell me about chemical engineering apptitude test..

0 Answers   IOCL,

---

Question 65 – A differential equation is given as y” + 5y’ + 6y = 0, y(0) = 2 and y’(0) = 3. By using Laplace transform, an engineer has correctly produced the equation L {y} = (2s + 13) / [(s + 2)(s + 3)] = A / (s + 2) + B (s + 3). (a) Find the values of A and B. (b) The inversed Laplace transform of 1 / (s + a) is given by exp (-at) where a is a constant. If the statement : L {y} = 9 L { exp (-2t) } - 7 L { exp (-3t) } is correct, find the equation of y as a function of t as a solution to the differential equation stated in the beginning of this question. When L {d} = 9 L {b} - 7 L {c}, then d = 9b - 7c with b, c and d are unknowns.

1 Answers  

---

Suppose you have hot fluid and cold water, what fluid you should flow in shell side and tube side in a shell and tube heat exchanger and why

6 Answers  

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.28 : In the development of a small engineering facility for biochemical processing, completed contract method is applied in its construction accounting. In a short contract period, let the (contract price) = A. Let the (costs to date) = B; (estimated cost to complete) = C. (a) Find the values of : (i) estimated total costs; (ii) total estimated profit; (iii) percent completion to date. (b) If the project contract is 100 % completed : (i) find the total gross profit recognized; (ii) what is the exact numerical value of C?

1 Answers  

---

Explain the steps taken to operate a tank-blanketing valve?

0 Answers  

---