What is true about Link-State protocols? A.) They maintain a more complex table than distant vector protocols B.) They maintain a less complex table than distant vector protocols C.) They use routing ports D.) The maintain backup copies of the IOS

1 Answers  

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---

Which protocol gets a hardware address from a known IP address? A.) RARP B.) TCP C.) IP D.) BootP E.) ARP F.) ICMP

3 Answers  

---

Choose the following that are benefits to segmenting with router: A.) Flow Control B.) Manageability C.) Multiple Active Paths D.) Explicit packet lifetime control

1 Answers  

---

Which of the following are Session Layer standards? A.) ASCII and EBCDIC B.) MPEG and MIDI C.) RPC and SQL D.) JPEG and PICT

3 Answers  

---

Identify the administrative distance and appropriate routing protocol? A.) RIP = 255, IGRP = 100 B.) RIP = 100, IGRP = 120 C.) RIP = 1, IGRP = 0 D.) RIP = 120, IGRP = 100

3 Answers  

---

Which service takes information from multiple sources and allocates bandwidth on a single media? A. Time-division Multiplexing (TDM) B. Signaling System 7 (SS7) C. X.25 D. Frame relay

1 Answers  

---

I have layer 3 Cisco 3560(Multilayer) switch right.How we can configure sub interface & Inter VLAN(we have vlan 2,3 & 10 ),Each VLan talk with each other?

4 Answers   IBM,

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

---

On Cisco catalyst 5000 how would you set the second port on the controller in the first slot to full duplex? A.) Set port duplex 1/1 full B.) Set port duplex 1/2 full C.) Set port duplex 0/1 full D.) Set port duplex 0/2 full

2 Answers  

---

Value in which type of access list?

0 Answers  

---

How many parts of ping?

0 Answers  

---