Which statement about Ethernet switches is true? A. Symmetric switching allows connection between pods of unlike bandwidth and does not require memory buffering B. Memory Buffering is used to prevent a bottleneck when pods of different bandwidth are connected on a symmetric switch C. The latency can be reduced if the switch utilizes the store and forward method of switching store and forward is better for error detection D. The cut through method of switching is faster because the switch forwards the packet to the destination as soon as it reads the destination address

1 Answers  

---

What is the name of best path in eigrp protocol?

0 Answers  

---

In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physical interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay

1 Answers  

---

How would you configure one host name that points to two IP addresses? A. IP host jacob 1.0.0.5 2.0.0.8 B. IP jacob 1.0.0.5 2.0.0.8 C. IP host jacob 1.0.0.5 D. IP host duplicate "all"

1 Answers  

---

Can you explain how L2F data tunneling process works?

1 Answers   CCIE,

---

What is the syntax to use to configure the port on a Catalyst 5000 switch? A.) slot port/type B.) type slot/port C.) port slot/type D.) port type/slot

2 Answers  

---

What is trigger rip and from which ios version it starts?

0 Answers  

---

Identify the following components of the IPX address 2e.0000.0065.ed43 A.) Not a valid IPX address B.) Network = 2e, Subnet = 0000, Node = 0065.ed43 C.) Network = 2e.0000, Node = 0065.ed43 D.) Network = 2e, Node = 0000.0065.ed43

1 Answers  

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

What is difference between igp and eigrp?

0 Answers  

---

what is Bandwidth capping

0 Answers   Infosys,

---

As the system administrator, you type "ppp authentication chap pap secret". Which authentication method is used first in setting up a session? A. secret B. PAP C. CHAP D. PPP/SLIP

1 Answers  

---