What are some guidelines for designing for liquid and gas velocities in process plant piping?

0 Answers  

---

The power required for size reduction in crushing is???

5 Answers  

---

The water is superheated steam at 440 degree Celsius and 17.32 megapascals. Estimate the enthalpy of the steam above. From the steam table for water at 440 degree Celsius, enthalpy of steam, h at 18 megapascals is 3103.7 kilojoules per kilogram and at 16 megapascal is 3062.8 kilojoules per kilogram. Assume that h = mP c where P is pressure; m and c are constants at fixed temperature with small differences in P.

1 Answers  

---

Question 89 - A hemocytometer is a device that is used for counting cells. In an engineering experiment, 100 microlitres of cell suspension is diluted with 50 microlitres of Trypan blue dye. Only death cells appear blue in color when stained with the dye. There are 57 cells detected in a hemocytometer, where 5.3 % of them appear blue when the chamber of the meter is placed under a microscope. Each square of a chamber can contain 0.0001 mL of liquid. (a) Calculate the number of viable cells. (b) The cells ocupied 5 squares. Calculate the average number of viable cells / square. (c) Calculate the dilution factor of the cell suspension by using the formula : Dilution = final volume / initial volume. (d) Calculate the concentration of viable cells / mL by using the formula : Concentration = (Average number of viable cells / square) x dilution x (square / volume).

1 Answers  

---

PROCESS DESIGN - EXAMPLE 21.1 : According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.

1 Answers  

---

What is the maximum permissible Earth to Neutral voltage in an electrical system.

0 Answers  

---

Explain what are flameless oxidizers?

0 Answers  

---

how does the properties of an element changes by increasing protons and electrons?

0 Answers  

---

What is the most common cause of solid size segregation in bulk solid systems?

0 Answers   TATA,

---

X is a solid having a white colour at room temperature. It has a density about 2g/cc. Although it has melting point near 325 degree Celsius, its properties start degrading above 260 degree Celsius. The coefficient of friction is very low about 0.1. It has very good dielectric properties especially at higher radio frequencies. It has a very high bulk resistivity. It is chemically inert. It is also resistant to van der Waals force. It is hydrophobic as well as lipophobic. Creep or ‘Cold Flow’ has been observed in X.

0 Answers   Ford,

---

What is pneumatic conveying?

0 Answers  

---

A cylinder having water is being evacuated with constant rate. what is the relation between pressure which is existing in cylinder with time? (P and t relation)

2 Answers  

---