For an ideal black body (A) absorptivity = 1 (B) reflectivity = 1 (C) emissivity = 0 which is true???????

4 Answers   GATE, KFCL,

---

Explain what type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?

0 Answers  

---

PETROLEUM ENGINEERING - QUESTION 25.1 : Fact 1 : Dry air contains 20.95 % oxygen, 78.09 % nitrogen, 0.93 % argon, 0.039 % carbon dioxide, and small amounts of other gases by volume. Fact 2 : Volume occupied is directly proportional to the number of moles for ideal gases at constant temperature and pressure. Fact 3 : 12.5 moles of pure oxygen is required to completely burn 1 mole of pure octane. Fact 4 : Air-fuel ratio (AFR) is the mass ratio of dry air to fuel present in a combustion process such as in an internal combustion engine or industrial furnace. Fact 5 : Molecular weight of oxygen gas is 31.998 g / mole and molecular weight of nitrogen gas is 28.014 g / mole. (a) Find the molar ratio of nitrogen and oxygen, or (moles of nitrogen) / (moles of oxygen) in dry air, by assuming ideal features of nitrogen and oxygen gases. (b) How many moles of nitrogen are available if dry air is used to completely burn the 1 mole pure octane? (c) Find the mass of fuel of 1 mole of octane with molecular weight of 114.232 g / mole. (d) Find the mass of dry air with 12.5 moles of pure oxygen by assuming only oxygen and nitrogen gases exist in the air. (e) Find the air-fuel ratio (AFR) when octane is used as fuel. (f) Find the fuel-air ratio (FAR) when octane is used as fuel.

1 Answers  

---

when liquid stored in spherical vessel,equilibrium shift towards liquid.what is the benefit of it?

1 Answers  

---

Explain can large temperature differences in vaporizers cause operational problems?

0 Answers  

---

What are the different characteristics that can affect the flow of bulk solids and how?

0 Answers  

---

What are some factors to consider when trying choosing between a dry screw compressor and an oil-flooded screw compressor?

0 Answers  

---

What is the meaning – strain? In a distillation column, if a metal block 10 cm on a side is deformed so that it becomes 9 cm long due to cooling effect, what is the strain involved in percentage?

1 Answers  

---

MICROBIOLOGICAL ENGINEERING - QUESTION 28.3 : In the calculation of the growth of bacteria, absorbance, A in spectrophotometry is used. According to Beer-Lambert Law, A = e x l x c where A is the absorbance of the solution (no unit), l is the distance of light travels through the solution (in cm), e is the molar absorptivity or the molar extinction coefficient [ in L / (mol.cm) ]. For a particular solute and fixed path length : As / Ao = Cs / Co where Ao is the observed signal for a known concentration Co, and As is the observed signal for a sample concentration Cs. (a) For a cell concentration of 560 cells / mL, a spectrophotometre gives an absorbance reading of 1.0. A mixture of concentration 3600000 cells / mL can be diluted in several operations, with each operation having a dilution of 1:20. How many dilutions should be made so that the concentration of this mixture can be calculated within a range of A = 0.0 to 1.0. (b) In another experiment, a sample tube of 1 cm in width is used. Let A = 0.06 and e = 0.0012 ml / (cell.cm). Find the cell concentration of the sample.

1 Answers  

---

X is a solid having a white colour at room temperature. It has a density about 2g/cc. Although it has melting point near 325 degree Celsius, its properties start degrading above 260 degree Celsius. The coefficient of friction is very low about 0.1. It has very good dielectric properties especially at higher radio frequencies. It has a very high bulk resistivity. It is chemically inert. It is also resistant to van der Waals force. It is hydrophobic as well as lipophobic. Creep or ‘Cold Flow’ has been observed in X.

0 Answers   Ford,

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.9 : In the modelling of the total of n rolls of a dice by an engineering student, let D be the random outcome of rolling a dice once. (a) Find the probability of outcome of D = 1, 2, 3, 4, 5 and 6. (b) Find the average score of each rolling of a dice D. (c) Find the expected value, Sn of n rolls of a dice in term of n and D. A new dice has a value of D* = D - 3.5. (d) Find the values of D* for each volume of D = 1, 2, 3, 4, 5 and 6. (e) Find the equivalent model of Sn in term of n and D. (f) Find the expected value of D*.

1 Answers  

---

Explain how do you design a vapor-liquid separator or a flash drum?

0 Answers  

---