What is the syntax to use to configure the port on a Catalyst 5000 switch? A.) slot port/type B.) type slot/port C.) port slot/type D.) port type/slot

1 Answers  

---

Hi Gyes, here is new question. can you provide answer of following question Like linux, can we windows as router? If yes how can we able to do this,

2 Answers  

---

which utility should use to test whether TCP/IP has been initialized on a system.friends plz post the answer with explaination..

3 Answers  

---

The Cisco Catalyst 5000 switch supports full duplex. How would you enable it on the second port of the card in slot 1? A.) router(config-if)# duplex full B.) router(config)# duplex full C.) router(config-if)# set port duplex D.) router(config)#port duplex = full E.) router(config-if)# set port 1/2 full

1 Answers  

---

Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual

1 Answers  

---

Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols

2 Answers  

---

On which layer does L2F, PPTP and L2TP operate?

0 Answers   CCIE,

---

Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102

1 Answers  

---

IP standard access lists use which of the following as a basis for permitting or denying packets? A.) destination address B.) port C.) protocol D.) source address

1 Answers  

---

What is true when using DDR? A.) HDLC is the preferred encapsulation B.) You must use static routing C.) You should use dynamic routing D.) You should use ISDN

1 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

When configuring the subnet mask for an IP address, which formats can be used?A. dotted-decimal. B. Hexadecimal C. Bit-count D. Octal E. Binary

1 Answers  

---