What’s the easiest way to remotely configure a router?

0 Answers  

---

On which base switches take decisions?

0 Answers  

---

In transport layer, for connection oriented communication Three way handshake process is there to establish a connection. So question is that, when a host send an ACK messages to another host with host intend to establish a connection, the source host send it as Broadcast or unicast message? Cud anyone explain this. Thanks in advance.

3 Answers   HCL,

---

Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0

3 Answers  

---

How often does IP RIP send out routing table updates by default? A.) They send complete updates every 30 seconds B.) They send partial updates every 30 seconds C.) They send complete updates every 60 seconds D.) They send partial updates every 60 seconds

1 Answers  

---

When setting up a frame-relay network between a Cisco router and a non-Cisco router, what encapsulation type should you use? A.) SAP B.) CISCO C.) IANA D.) Apollo E.) IETF F.) Q933A

2 Answers  

---

Which classes are assignable?

0 Answers  

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

Identify the 2 characteristics regarding MAC addresses? A.) Contains a network portion and host portion B.) Always assigned by System Administrator C.) 48 bits long D.) Contains a vendor code and serial number

2 Answers  

---

What are the possible ways of data transmission in ccna?

0 Answers  

---

Identify the 2 commands the saves the running-config to NVRAM? A.) write memory B.) copy running-config startup-config C.) write network D.) write backup

2 Answers  

---

In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physcial interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay

2 Answers  

---