MASS TRANSFER - EXAMPLE 4.1 : A concentric, counter-current heat exchanger is used to cool lubricating oil. Water is used as the coolant. The mass flow rate of oil into the heat exchanger is 0.1 kg / s = FO. For oil, the inlet temperature TIO = 100 degree Celsius and the outlet temperature TOO = 55 degree Celsius. For water, the inlet temperature TIW = 35 degree Celsius and the outlet temperature TOW = 42 degree Celsius. What is the mass flow rate of water in kg / s, FW needed to maintain these operating conditions? Constant for heat capacity of oil is CO = 2131 J /(kg K) and for water is CW = 4178 J /(kg K). Use the equation (FO)(CO)(TIO ?TOO) = (FW)(CW)(TOW ?TIW).
MASS TRANSFER - ANSWER 4.1 : Rearranging the given equation, then FW = (FO)(CO)(TIO – TOO) / [ (CW)(TOW – TIW) ] = (0.1)(2131)(100 – 55) / [ (4178) (42 – 35) ] = 0.327891 kg / s. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
Is This Answer Correct ? | 0 Yes | 0 No |
name of the fraction at which benzene xylene and toulene is obtained during coal tar distillation
What are some common problems associated with dense phase pneumatic conveying?
POLYMER ENGINEERING - QUESTION 24.1 : The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18. The fraction of polymer chain X of 3 different monomers a, b and c in a polymer are Xa = 0.5, Xb = 0.3 and Xc = 0.2. (i) Calculate number average molecular weight by using the formula Ma Xa + Mb Xb + Mc Xc. (ii) Calculate weight average molecular weight by using the formula (Ma Xa Ma + Mb Xb Mb + Mc Xc Mc) / (Ma Xa + Mb Xb + Mc Xc). (iii) Calculate the polydispersity by using the answer in (ii) divided by answer in (i). (iv) If the molecular weight of repeat unit is 12, calculate the degree of polymerization by using the formula (Ma Xa + Mb Xb + Mc Xc) / (molecular weight of repeat unit).
ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.31 : In a biochemical engineering company, let the actual revenue generated = A, actual cost incurred = B. According to the standard budget, the revenue generated = C, cost incurred = D. (a) Find the profit according to : (i) actual situation; (ii) standard budget. (b) Calculate the Variance Due to Price and Efficiency in : (i) revenue generated; (ii) cost incurred; (iii) profit. (c) If E > F where > represents : more than, find the 4 pairs of values of E and F in favorable conditions.
what is the difference between car seal close/open valves and lock close/open valves?
What is maximum recommended velocity for steam in a plant pipe network?
who is the first atomic scientist in india?
Dear guys we adding hypo at climax plant and that water is inlet to DM plant so with hypo water that can affect my resins of cation and anion. if it is affect life of my anion and cation so what kind of steps should be take.
0 Answers Hindustan Unilever Limited,
In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?
Question 35 – A mixture consists of benzene (B), toluene (T) and xylene (X). At a temperature of 353 K, the data of vapor pressures : B : 754.12, T : 289.71, X : 91.19. Unit is mm Hg. The pressure P is 0.5 atm. The value of k for each substance is k = (vapor pressure) / P. (a) Calculate k for B, T and X. Let L / V = 0.65. (b) By using the equation V = F / [ (L / V) + 1 ], find the value of V when F = 100, then what is the value of L?
The process conditions of the fuel gas are as follows: Temperature = 25 deg C Pressure = 4 bar g Calculate the line size for the fuel gas supply line to the superheater
what is difference between precipitation and crystalisation