FOOD ENGINEERING - QUESTION 23.2 : (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80 °C to 71 °C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71 °C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24 °C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80 °C, and the air is cooled to 71 °C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To) / (Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

can i drink deminaralised?

1 Answers   Dalkia,

---

Question 38 - The terminal velocity of a falling object, v is given by v = sqrt [ 4g (R - r) D / (3Cr) ] where sqrt is the square root of, g = 9.81, D = 0.000208, R = 1800, r = 994.6, m = 0.000893. The Reynold number, L is given by L = rD (v) / m. The C for various conditions are : C = 24 / L for L < 0.1; C = 24 (1 + 0.14 L^0.7) / L for 0.1 <= L <= 1000; C = 0.44 for 1000 < L <= 350000; C = 0.19 - 80000 / L for 350000 < L. Find the value of v for the situation above by trial and error, ^ is power, <= is less than or equal to.

1 Answers  

---

Explain what types of valves are recommended for slurry services?

0 Answers  

---

what is defferance between tubular & automotive plate battery

0 Answers  

---

MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)

0 Answers   Simbhaoli Sugars,

---

can you explain about the design calculations and procedure of boiler

0 Answers   Reliance,

---

For a Vernier scale of representative fraction (RF) = 1 / 25, calculate the length of the scale for the reading up to 4 metres.

1 Answers  

---

Explain how can one determine if a particular solid can be fluidized as in a fluidized bed?

0 Answers  

---

What is difference between a Flue Gas Analyzer and Exhaust Gas Analyzer ?

1 Answers  

---

hai i A neelakanteswara rao ,selected for the interview on 15th july 2008. I completed my diploma in chemical engineering.let me know how to face the interview& the type of technical questions.

0 Answers   IOCL,

---

ENGINEERING NUMERICAL METHODS - EXAMPLE 19.1 : Solve the simultaneous equation using simple Excel program : r + s - t = 7, 2r - s = 0, 3r + 2t = 15. Explain the use of functions of MINVERSE and MMULT together with the keyboard C (Ctrl) + S (Shift) + E (Enter).

1 Answers  

---