Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


What command displays the OSPF Process ID, Router ID, Address summarizations,
Routing Networks, and passive interfaces configured on a router?



What command displays the OSPF Process ID, Router ID, Address summarizations, Routing Networks, an..

Answer / parshant jaswal

show configuration or show running-config

Is This Answer Correct ?    5 Yes 2 No

Post New Answer

More CCNA Interview Questions

FastEthernet compares to 10baseT Ethernet in which of the following ways

1 Answers  


Why OSI layers having 7 layers instead of one layer.

8 Answers   HCL,


The Cisco Discovery Protocol (CDP) periodically sends out a multicast packet (at layer 2). Which command will alter the default interval of 60 seconds? A.) cdp hold 111 B.) cdp wait 111 C.) cdp interval 111 D.) cdp 111 E.) cdp timer 111

1 Answers  


How do areas benefit a link state inter network?

0 Answers  


What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface

1 Answers  


GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call

1 Answers   IBM,


Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!

5 Answers  


The CSMA/CD Ethernet IEEE committee is defines as which of the following? A.) 802.2 B.) 802.3 C.) 802.4 D.) 802.5

1 Answers  


Explain types of communication in ipv4?

0 Answers  


What is the difference between DTE & DCE???

12 Answers   ISDN, Wipro,


Tell me why we use filter option?

0 Answers  


What is difference between baseband and broadband transmission in ccna?

0 Answers  


Categories