Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


how to caluculate flow by using transmitter?tell me plz I am
eagerly waiting for your reply..

Answers were Sorted based on User's Feedback



how to caluculate flow by using transmitter?tell me plz I am eagerly waiting for your reply....

Answer / ginoop

easiest formula to find Ma
of flow in square root
(sqrt of % x 16)/10 +4


eg : ma of 25%
sqrt of 25x 16/10+4
=5x16/10+4
=80/10+4
=8+4=12
ma of 25% flow in sqrt =12

eg : ma of 50%
sqrt of 50x 16/10+4
=7.07x16/10+4
=113.13/10+4
=11.31+4=15.31
ma of 50% flow in sqrt=15.31

Is This Answer Correct ?    4 Yes 2 No

how to caluculate flow by using transmitter?tell me plz I am eagerly waiting for your reply....

Answer / nib

CORRECT FORMULA
ma=%*16/100+4

Is This Answer Correct ?    2 Yes 2 No

Post New Answer

More Instrumentation Interview Questions

explain level transmitter working

1 Answers  


A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

0 Answers   MNC,


SOME OF YOUR QUESTIONS ARE NOT MAKING ANY SENSE SO TRY AND PUT IN A LITTLE BIT MORE EFFORT BEFORE YOU POST A QUESTION. WE WILL ONLY HELP THOSE WHO WE CAN SEE ARE TRYING TO HELP THEMSELVES.

0 Answers  


control modes

1 Answers   Vedanta,


1.what is controller proportional gain 2.what is the controller intergral action time. 3.A proportional plus derivative controller that has a proportional band of 20% and a derivative action time of 0.1 minutes. Construct the shape of the output waveform for the triangular input if the input rises and falls at the rate of 4 units per minute.

0 Answers  


what is the differnt between open loop and close loop ?

5 Answers   India Cements,


what is commissioning & pre commissioning , explain with difination

2 Answers   Bapco Bahrain Petroleum Company, Shell,


what r the different types of instrumentation cables? give their specification?

3 Answers  


what is meant by calibration

3 Answers  


What is the difference between radar and ultrasonic level transmitter? Which method is best and more accurate?

8 Answers  


In turbine, what does term CDP, NI, NH, HSSOC, means

0 Answers   ADMA OPCO,


what is cavitation in control valve? & how we can avoid it?

1 Answers   Forbes Marshall, Reliance,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)