Describe the method of Plate Earthing.



Describe the method of Plate Earthing...

Answer / saravananp

Plate earthing provids using copper plate (450mm x 450mm x
6mm). The area of the copper plate is high causing high
earthing value (Low resistance).

Instaling Method: The copper plate at the depth of 2 Mtr or
3 Mtr. The centre support provides using 40mm GI pipes,
funnel in top.The two numbers of 25mm x 3 mm copper flat
stamped from top of the GI pipe to copper plate to improve
the earth value. The salt, charcole to improve the
conductivity.

The materials using for plate earthing are as below:

1) Meshed Funnel
2) 40 x 300 x 6 mm copper earth pad
3) 25 x 3 Cu strip
4) Copper Rivit
5) 450 x 450 x 3 mm Cu plate
6) 8x25 mm bolt and nut with washer
7) 6x75 mm bolt and nut with washer
8) 40 mm GI pipe - 2.8 mtrs
9) 25mm dia x 200 mm length GI pipe with double end threaded
10) 40mm to 25 mm GI reducer
11) 1" Check nut(6mm thick)
12) Charcoal
13) Salt
14) 450 x 450 mm heavy duty SFRC chamber cover with frame



ersaravananp@gmail.com
Saravanan.P

Is This Answer Correct ?    6 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

how freewheeling diode improves the powerfactor

0 Answers  


Why Lead-Acid cell voltage is 2.1 volt, why we can not chenged it cell voltage by using extra row-material, only incries its AH.

1 Answers  


What is the similarity and what is the difference between relays and PLC?

3 Answers   NTPC,


what should be distance between phase to phase in 415v system?

1 Answers   NTPC,


I am working in 600MW power plant currently in erection phase. I came along this term and want to know its meaning in simple language, consider me naive!?? All motors shall be of energy efficient type EFF-2 as per IS:12615/ equivalent IEC / International Standard.

1 Answers   Punj Lloyd Ltd,






my question is that....few days ago i had installed a three phase motor starter for an electric saw.the motor will run and make the hydraulic pressure which will be goes to pressure cylender by up and down lever.two number of limitswitches are also installed on cylinder for safety of motor.now when the arm of cylinder reaches to the upper or lower limit it will cut the motor's line.and motor will be stop.now wana know that what will i do that motor runs continue after the limitswitch cut it down but it shold not be made any pressure.pls answer me in brief.

3 Answers  


Difference between SHORT CIRCUIT and an OVERLOAD ?

1 Answers  


Power Factor Controller

1 Answers  


Hot Water System (HWS). Will a 30ma elcb have more nuisance tripping than 100ma elcb

1 Answers   CIMC,


Where can I get Iidian straderd specifications for electrical items or works in web? please help me.

0 Answers  


WHaT IS THE CONCEPT OF INDUCTION LAMPS IN MODERN LIGHTINGS, and HOW IT WORKS TO EMIT LIGHT ( AS NO ELECTRODES ARE PRESENT ) ?" COULD INDUCTION LAMPS CAUSE INTERFERENCE WITH COMUNICATIONS INTO A STORE USING INDUCTION LIGHTING ? WHAT IS THE BENEFIT OF USING THE LOW FREQENCY INDUCTION LAMP , VERSUS LED , AND VERSUS FLUORESCENT, AND VERSUS ANOTHER KIND OF LIGHTING . THANK yOU MOISES GUINDI

0 Answers  


Why does the speed regulating system adopting I controller have no steady-state error? In this single closed-loop speed regulating system, when the input of the I controller Un=0, what is the output voltage of the regulator? What factors do the output voltage depend on?

0 Answers   Sterling Wilson,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16636)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)