Answer / koti

VCB upto 33 KV only. SF6 for EHVs.

Answer / rajiv pandey

both are circuit breaker.VCB in use only 11kvbut SF6 use in
above 11kv .SF6 is costly project then VCB.

1. what is the power factor of a purely inductive load? (i) Zero (ii) Lagging (iii)Leading (iv) Unity 2. which type of transformer connection is preferred in case of power supply transformer? (i) Star/Star (ii) Delta/Delta (iii) Star/Delta (iv) Zig Zag/Star

2 Answers  

---

How can w select the cable size for different rating load & also waht r factors affecting the during selection of cable?

11 Answers   AB Inc, Bosch, BRB Cable, Lucas TVS, Trisome Technical Services,

---

why we use mostly 3-phase but not 4-phase and 5-phase what is the difference between them

1 Answers  

---

where used impendence relay?

3 Answers  

---

placing earthing pit in pathway is correct or wrong??. placing earthing wireGI1/18 inside walls is correct or wrong?. explain!!!

0 Answers  

---

I use 20 nos led tube 4feet, in pathway 100mtr approximate, so what size cable i use for lighting

0 Answers   Oman Cables Industry SAOG,

---

Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  

---

why does in transformer the v/f ratio constant?

2 Answers   TATA,

---

what should be the motor rating for pumping water for house hold use from 60km far lake and what formula is to use please tell me

1 Answers  

---

what is the effect of connecting three phase supply lines to three phase auto transformer output terminals through a fuse of 10Amp and a circuit breaker (MCB). Is this connection permanently destroy the transformer?

1 Answers  

---

How to calculate cable size? How to O&m of vcb?

0 Answers  

---

Iam Preparing For Ap Transco Assistant Engineer (ELECTRICAL) Exam how To Prepare What Is The Refernce Books.can You Give The Advises To Me.tahnk You. This Is Radhika Iam Preparing For Ap Transco Assistant Engineer (ELECTRICAL

2 Answers  

---