Interested to Buy Any Domain ? << Click Here >> for more details...
please give me the ans. of following mcq
A nozzle is a device which:
(A) Increase pressure & reduce kinetic energy
(B) Decreases pressure & increases kinetic energy
(C) Reduces both pressure & kinetic energy
(D) Increases both pressure & kinetic energy
- 7 Answers
- 12766 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / newgradengineer
|-------
FR1=A1V1 | \ FR2 =A2V2
----->| | ----->
P1V1=nRT1 | / P2V2 = nRT2
|-------
FR = flow rate
since this is a close system, FR1 = FR2
A1V1 = A2V2
-> A1/A2 = V2/V1 Since A1/A2 > 1 --> V2/V1 > 1 or V2>V1
Kinetic Energy = 1/2*m*v^2. Higher velocity gives higher
kinetic energy
We have P1V1 = nRT1 and P2V2 = nRT2
Assume there is no change in T
---> P1V1 = P2V2
---> P1/P2 = V2/V1 since V2/V1 > 1 --> P1/P2 >1 or P1>P2
(B) decreases pressure and increases kinetic energy is the
correct answer
| Is This Answer Correct ? | 12 Yes | 0 No |
Answer / dinesh. iiet(student )
decrease in pressure & increase in kinetic energy
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / devanesan
B) Decrease pressurre & increase kinetic energy.
velocity of steam leaving the nozzle V=44.72*sq.root of K*H
where H is enthalpy drop and K is nozzle coefficient.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / aamir pathan
incerase both pressure and kinetic energy...
nozzle used to increase pressure and kinetic energy
| Is This Answer Correct ? | 0 Yes | 2 No |
Horse power of i.c. Engines can be expressed as rac rating, sae rating, or din rating. To which countries these standards belong ?
Steering handle (round dial) of motor vehicles (CAR,BUS,LORRY) wiil be designing with two cross supports without 180 degree straightness( it will be little bit cross). Why?
Explain how is a submarine able to submerge and surface?
What is a slined joint?
Define flash in mould making ?
Hello Friends I had my ONGC test today,but it was very bad.But I would give certain suggestions so that u may not face he problem which i had. Be thorough with Electrical Technology.Generators.motors stators etc.There are 5 questions on that. There were also good no.of questions from Hydraulic machine and Production technology. Then 3 from Strength of materials.And remember the dimensional quantities.
what is turbo machine
What are the different type of mechanism to engage primary moving engine and transmission [ In other word how many different type of clutches are there
what will be the change in weight ( mass ) of a person when us he is coming down / up in the elevator ?
what we switch on after switching on the ups to start a computer, is a cabinet or a cpu ?
Distinguish between the shear center and elastic center.
what is the function of steam trap?
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
