Interested to Buy Any Domain ? << Click Here >> for more details...
Why we generate power at
multiple of 11 i.e 11kv,33kv
etc.
- 9 Answers
- 22486 Views
- DTV Solutions, Havells, TCS, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / lisa
Always the generating power is a multiple of form factor
1.1.
| Is This Answer Correct ? | 81 Yes | 5 No |
Answer / kundanmalani1990
b'cz the form factor is RMS value /average value =1.11 and
the form factor is the pure sine wave.
| Is This Answer Correct ? | 66 Yes | 5 No |
Answer / lokesh choudhary
Becoz of form factor 1.11
so we do transmission on multiple of 11
so that we can decrease the losses
| Is This Answer Correct ? | 4 Yes | 1 No |
Answer / prateek gupta
we all know that form factor = rms value/peak value
the power which is generated at 11 kv it is a multipication
of formfactor that is 1.1.
also the insulation losses is also minimum at 11 kv.
| Is This Answer Correct ? | 2 Yes | 2 No |
Answer / viral
aBOVE answers are correct and also the insulator disk are
designed to bear 11KV so in multiple of that we can decide
the transmission voltage for insulator string conviniency
| Is This Answer Correct ? | 12 Yes | 13 No |
Answer / nikhil anand
Due to form factor
Rms value/avg value gives form factor 1.11
So we generate power at multiple of 11.
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / parveen
we generate electricity in the multiple of form factor
becausehe effect of ac current should be as dc current
| Is This Answer Correct ? | 2 Yes | 5 No |
Answer / siva
the transformer stepup and step down ratio should be a whole
number so tat we go for multiples of eleven.for example
11kv/440v means the ratio will be 25:1.
| Is This Answer Correct ? | 0 Yes | 4 No |
Answer / iti
we generate power at multiples of 11 because there is 10%
loss in transmission of power over transmission line.i.e.
for every 100V, 10V is lost in losses. thus we increment it
10% and then send from the sending end such that we may
receive the required at receiveng station.
| Is This Answer Correct ? | 23 Yes | 38 No |
what is meant by power and distribution transformer ?
how to find out cable size if load is 2800 watts, 230 volts AC supply and load distance is 1800 meters
Why current shoots up in the secondary on the knee point voltage during saturation test of CT? How core saturation effects the secondary current (while the primary side is open)? What the logic behind this?
why we don't use earthing as neutral?
What is meant by load angle of an alternator? Upon what factors does the load angle depend?
what is difference between fuse and breaker?
how we can measure the dc current instead of clamp meter ?
what is first pole to clear factor
How earth resistance reduses by pouring water coal and salt?
what is meant by dielectric breakdown ? where we using HV test kit & what purpose?
in alternator why on load terminal voltage is less than no load teprminal voltage
why do we use 3 single phase instead of one 3 phase?? though vee connection is its advantage but what is the hidden reason behind it??
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
