Answer / guest

Answer: A B

Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.

1 Answers  

---

what is full form of rst,smtps & http?

2 Answers   HCL,

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---

Which layer of the 7 layer model provides services to the Application layer over the Session layer connection? A.) Transport B.) Application C.) Session D.) Network E.) Datalink F.) Presentation

2 Answers   CTS,

---

What does 'P' mean when running a Trace? A.) Good route B.) Protocol unreachable C.) Source Quench D.) Destination unreachable

2 Answers  

---

---

Which OSI layer establishes, maintains and terminates sessions between applications? A.) Application B.) Physical C.) Data-Link D.) Presentation E.) Network F.) Session

2 Answers  

---

Identify the order of the 5 step encapsulation? 1) Create the segment 2) Convert the frame to bits 3) Create the packet 4) Create the frame 5) User creates the data A.) 1,2,4,2,5 B.) 2,1,3,4,5 C.) 5,1,3,4,2 D.) 5,3,4,1,2

1 Answers  

---

Which global configuration command will tell the router to load the IOS file 'IOS_filename' from the Network File server at 1.2.3.4 during the next boot? A.) boot system flash IOS_filename 1.2.3.4 B.) boot system tftp IOS_filename 1.2.3.4 C.) config-register 0x0 1.2.3.4 D.) boot system rom 1.2.3.4 E.) This can not be done, only the first file in flash can be used.

1 Answers  

---

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ICMP D.) RARP E.) TCP F.) BootP

1 Answers  

---

Identify 2 HDLC characteristics? A.) Default serial encapsulation B.) Open standard C.) Supports Stacker compression D.) Supports point-to-point and multipoint

3 Answers  

---

Explain the difference between flsm and vlsm?

0 Answers  

---

Put the following steps of encapsulation into the correct order: 1) The data is broken into segments to be organized 2) Frames are converted to 1s and 0s to be put on the wire 3) Packets are converted into frames 4) Information that users enter is converted into data 5) The segments are changed to packets to be routed A.) 4, 1, 3, 2, 5 B.) 4, 5, 1, 3, 2 C.) 2, 3, 1, 4, 5 D.) 4, 1, 5, 3, 2

3 Answers  

---