Answer / manisha

reciprocating pump is a positive displacement pump.here the word +ve refers to no losses,leakage and backflow.means total discharge occur.one more thing in this case actual movement or displacement of fluid takesplace.
on d other hand a centrifugal pump is a dynamic pump.here suction takes place through a vortex casing.inside the casing a impellar is there.due to rotatio of dis impellar fluid is also rotated and centrifugal force acts on it.by which suction occur.

Answer / abdul hameed

In general: Centrifugal pumps are volume oriented (Flow).
Reciprocating pums are Pressure oriented (Head)

Answer / kunal sharma

reciprocating pump is a positive displace ment pump.. and
centrifugal pump is a forced vortex flow pump. forced
vortex flow means when a certain mass of liquid is forced
to rotate its head increases

Answer / santosh raikar

Centrifugal pump principal is dynamic action between
rotating impeller and fluid.
reciprocating pump principal is mechanical action b/w moving
piston and stationery fluid( more suitable is liquid).
centrifugal pump creates pressure head due to the conversion
of kinetic energy of fluid. the pressure head is nothing but
the resistant to the flow of fluid.

Answer / ankit singh

centrifugal pumps generate desired discharge head by applying centrifugal force on water through runner...
they are used to generate high discharge with low pressure.
whereas reciprocating pumps generate discharge head by pressurising water in a cylinder through reciprocating piston..they are used for generating low discharge at high pressure..

differentiate between total moisture and inherent moisture of coal.

0 Answers  

when pump is maitaind throughly and installed perfectly then why pump vibrates on above standard vibration level?

4 Answers   IOCL,

In process control loop e/p converter receives 4-20 ma input current from which control block?

0 Answers  

Why u want to leave the job? & Why u want to join our orgnization?

3 Answers   DELL, MAHINDRA, Tesco, Wipro,

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   CSPDCL-Chhattisgarh State Power Distribution Company Limited, RRB,

What kind of knowledge we need to gain to draw p&ID and Isometrics in autocad?

2 Answers   BEML,

In which process internal energy remains constant ?

0 Answers  

HI, I am Darshan S D completed BE in Mechanical & also completed my MBA in Finance & Marketing.Presently i am working in Geodis Global Solutions which gives support to the IBM, as a logistics coordinator. i have a plan to do SAP but confused which Specilisation to do ie whether in Finance or Material management. Also scared whether it is right for me to do that, is that will help me in getting good job. what is the future opportunity and present job position in the market.... pld kindly help me to know...

0 Answers  

how can you calculate angle of bite practically???

1 Answers   JKN Limited, SVNIT,

What are the 1st 2nd and 3rd laws of thermodynamics?

0 Answers  

what is the diffrence between Torque and Power ( layman Idea)?

2 Answers  

How to recommend which type of coupling is suitable in particular area

0 Answers