Interested to Buy Any Domain ? << Click Here >> for more details...
What must be true for two Routers running IGRP to communicate
their routes?
A.) Same autonomous system number
B.) Connected using Ethernet only
C.) Use composite metric
D)Configured for PPP
- 3 Answers
- 7734 Views
- Allied Group, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
If bandwidth will increase what will happen?
Explain why UDP is lease favored when compared to TCP?
Which statement is true regarding the user exec and privileged exec mode? A.) The '?' only works in Privileged exec B.) They are identical C.) They both require the enable password D.) User exec is a subset of the privileged exec
what is difference between designated router and backup designated router and explain feature of both router.
Identify the command to configure the router for IGRP autonomous system 100? A.) Router(config)# router igrp 100 B.) Router> router igrp 100 C.) Router# router igrp 100 D.) Router(config)# router igrp
To which layer ICMP belongs
What is the administrative distance for RIP? A.) 100 B.) 90 C.) 120 D.) 110
thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What is the distance limitation for 100BaseT? A. 305.955 ft B. 7283.46 inches C. 184 Meters D. 185 Kilometers
Which line from a show spantree 1 command output indicates that virtual LAN 1 (VLAN1) is functioning properly? A. Root pod is FastEthernet 0/26 B. Port Ethernet 0/1 of VLAN1 is Forwarding C. Designated port is Ethernet 0/1, path cost 10 D. Designated root has priority 0 address 00D0 588F B600 E. VLAN1 is executing the IEEE compatible Spanning Tree Protocol
What does a Standard IP Access-list use as test criteria? A.) IP source address B.) IP source and destination address, protocol numbers and port numbers C.) IPX source and destination address D.) Source MAC address
CCNA 
