Interested to Buy Any Domain ? << Click Here >> for more details...
how many vlan can be configured on a single switch
- 12 Answers
- 53653 Views
- IBM, Sigma IT, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / jitendra
its completely depend open which model you are going to use
but in simple Cisco switch L2 we ca configure 1000 vlan for
vlan 2 to vlan 1002
vlan 1 is default
| Is This Answer Correct ? | 75 Yes | 18 No |
Answer / reehana
vlan 1 administrative vlan. default all ports participate
in it.
vlan 2 to 1001 normal vlan.
1002 to 1005 reserved for future.
1006 to 4094 extended vlan
| Is This Answer Correct ? | 54 Yes | 8 No |
Answer / mohana krishnan
It depends upon the switch like L2 & L3
Vlan can be created upto
1)Vlan 1 - Default
2)Vlan 2 to 1001 - Normal Vlan
3)Vlan 1002 to 1005 - FDDI & Token ring
4)Vlan 1006 to 1024 - Reserved
5)Vlan 1025 to 4094 - extended.
| Is This Answer Correct ? | 41 Yes | 3 No |
Answer / rajesh
VLANs can be created from 2-1001.i.e 1000 vlans can be
configured.vlan1 is known as administrative vlan and it is
default.
| Is This Answer Correct ? | 34 Yes | 8 No |
Answer / nawaz
we can crate vlan 2 to vlan 1001 total 1000
vlan 1 is by defaul crated
vlan 1002 - vlan 1005 reserved for future
1006 - 4094 for extended vlan
| Is This Answer Correct ? | 18 Yes | 0 No |
Answer / subbaiah araveti
It depends upon the switch like L2 and L3
Vlan can be created upto
1)Vlan 1 - Default
2)Vlan 2 to 1001 - Normal Vlan
3)Vlan 1002 to 1005 - FDDI & Token ring
4)Vlan 1006 to 1024 - Reserved
5)Vlan 1025 to 4094 - extended
| Is This Answer Correct ? | 7 Yes | 1 No |
Answer / nandlal chauhan
vlan besic range start from 1 to 1005 in that
1,1002,1003,1004,1005 is reserved. so we can creat 1 to 1001
vlan.
| Is This Answer Correct ? | 9 Yes | 4 No |
Answer / harshal
its depends upon which type of switch u r using .
"show vtp status" is used priviledge mode to show number
of vlan supported by switch.
| Is This Answer Correct ? | 8 Yes | 5 No |
Answer / guest
All IP Add By Dh521:Dir/S It Instance Of Redhat 565 Commmand
| Is This Answer Correct ? | 3 Yes | 3 No |
Answer / prasanta
by default 5 vlan in a switch and 4094 we have to create in a single switch
| Is This Answer Correct ? | 3 Yes | 4 No |
in router we use config# ip host router2 ipaddress we use it for ping the neighbor router using name provided by us ..........instead of ip address in this max how many ip address can be assigned thanks
hi friends i have some problem regarding technical round ahr round plz tell me what should the right answer technical questions 1 what is brouter 2 what is the menaing of 10 base2, 10 base 5 and 10baset 3 what is diffrence between bit rate and baud rate. and this question was tooooooooooo much difficult to me that hr said to me that rank me after the taking the all short of interview
What are the different types of passwords used in securing a CISCO router?
What is the standard ISDN term for a non-native analog telephone? A.) TE1 B.) TA C.) LE D.) TE2 E.) ET
What is the difference between full duplex and half duplex?
completly describe th steps fo osi model when you enter http:/youtube.com
What is 10base5 ethernet lans?
The Cisco Discovery Protocol (CDP) periodically sends out a multicast packet (at layer 2). Which command will alter the default interval of 60 seconds? A.) cdp hold 111 B.) cdp wait 111 C.) cdp interval 111 D.) cdp 111 E.) cdp timer 111
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
The following is partial output from a routing table ; '192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1' Which routing protocol is being used? (assuming defaults have not been changed) A.) OSPF B.) RIP C.) BGP D.) IGRP
Which protocol switch use for filling its mac-table?
which utility should use to test whether TCP/IP has been initialized on a system.friends plz post the answer with explaination..
CCNA 
