Answer / indrajeet

It depends upon which type of motor you are connecting
means if you are connecting synchronous motor in parallel
then P.F.will improve.Instead of this if you connect
induction motor then the system P.F.will be lagging.

Answer / sreeknp

Explanation for the first answer
in syatem one motor is connected .if a second one of same
pf of earlier motor is connected parallel to the it then pf
will not change try with some simple figures

Answer / jain c

the Pf will change depend on the type of motor which is to
be connected as mentioned above.

Answer / sreeknp

sometimes it may change

Answer / azaz.electrical

power factor will change due to the eq. of power factor
P=VIcos(angle beetwin v&i)

Answer / ashok

it depends upon the motor connected

Answer / guest

yes

Answer / naresh chandra jha

it depend which type of notor you are connecting . for
example induction motor will operate in lagging power
factor, synchronous phase modilfier with under excited will
operate in lagging and when it is overexcited it will
operate in leading p.f .

Answer / sreeknp

1' if the motor is of same pf --no change in pf
2'if second motor has lower pf then pf will lowered
3' if second motor has higher pf --pf will improve now it is
clear that may lower, higher or no change
so correct answer is sometimes it may chamge

what is the role of frequency in electrical system

2 Answers   Hindalco,

differance b|w ground, neutral&earth

11 Answers   Bhel, SKH Metals,

wat is power factor

7 Answers   IOCL,

there is an alternator 480 k.w, 400v,50hz, 4-wire running on load having leakage alternator body earthed current 38 A. is it within acceptable limit? if yes then give reference if no then how to bring within specified limit

0 Answers  

what is the std. earthing resistance for 440V system or m/c, 33000/440 Volt substation? What is the std.?

2 Answers  

what will happened if generator runs with slow speed?

3 Answers  

TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2

0 Answers   KSEB,

we know the value of the power factor is 0.8, we know the power factor is not depends upon the load ,then why we cant design the power factor in transformer ?

1 Answers  

Why double earthing is required ?

1 Answers  

Can I use star delta connected induction motor for dual supply voltage?

0 Answers  

what is a 3 phase power formula ?

5 Answers  

Why in Digital Megger for finding Insulation resistance,-ve is applied to core or conductor and +ve is applied to ground.

1 Answers   ACC,