what will happen if we use petrole in diesel engine and
diesel in petrole engine
- 5 Answers
- 12620 Views
- Royal Enfield, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / prakash
Deisel engines are designed for self igniting fuel. & has
higher compressor ratio, petrol is not a self igniting
fuel. it needs spark to burn so putting petrol in deisel
engine will not work.
Deisel has property of self ignition @ higher pressure &
temp. & if placed inside petrol engine, by introduction of
spark engine can work.
| Is This Answer Correct ? | 28 Yes | 7 No |
Answer / mandeep
above answer is correct. but the question now arises... will the diesel work perfectly in petrol engine?
answer is "NO", because of the carbon accumulation near the spark plug, the engine will soon stops. . .
| Is This Answer Correct ? | 13 Yes | 4 No |
Answer / vasanthakumar
Diesel engine have injector to spry diesel and burnt the air fuel mixture at temp with spark plug, but if u use diesel in petrol engine ,there ignition temp is higher than petrol so it will not combusted at the petrol engine temp , so we cannot use petrol instead of diesel ,both are specific property in combustion chamber...
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / lokesh nayak
If diesel is put in a petrol engine it can never work because the compression ratio in petrol engines is very less to raise the diesel to its self ignition temp. which can only happen in diesel engines.If diesel could b used in petrol engines why would we put petrol to our bikes instead of diesel which would save us atleast 20 Rs/ltr. Simple logic, Mr.Prakash ur ans is wrong.
On the other hand if petrol is put in a Diesel engine, due to the high compression ratio , the temp. at the end of compression would be so high that if a spark is produced at this temperature by the spark plug , it can cause an explosion .
| Is This Answer Correct ? | 4 Yes | 5 No |
Answer / hari. salem. tn
Put diesel in a petrol engine and it will not explode,
nor even burn. The engine will not run. You might as well
have tried to burn water.
Put petrol in a diesel and it will explode at a much
higher pressure than the burning diesel could develop.
The result would be pieces of engine scattered all around as
it exploded from the pressures it was never designed to use.
| Is This Answer Correct ? | 3 Yes | 10 No |
how does a turbine works ?
What is polytropic process ? Under what conditions it approaches isobaric, isothermal, and isometric process ? In which reversible process no work is done ?
where impulse turbine & reaction turbine are used?
How to calibrate Vacuum Gauges if you don't have any standard gauge available with you? please suggest procedures for calibration of Vacuum gauge like pirani gauge ,cold cathod gauge,thermocouple gauge without any standard gauge.
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
Explain the fresh water cooling system.
Which has more mechanical efficiency betn 2-strock &4-strock IC engine & why?
What is the world's hardest metal?
In case of AHU ,how to arrive at chilled water USGPM of the AHU in case the AHU CFM is given. Can some HVAC genius please advise.
how we can calculate natural vibration frequency for steam turbine rotor please.
what is unit of mechanical work nand piower ?
5 Answers Hindustan Unilever Limited,
what is the difference between dross and scale?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
