I decided to provide a 11KV / 440V Xformer in my Substaion. What are the prote

Categories >> Engineering >> Electrical Engineering
Suggest New Category

I decided to provide a 11KV / 440V Xformer in my Substaion.
What are the protection required for that?

Question Posted / nishad

5 Answers
8941 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

I decided to provide a 11KV / 440V Xformer in my Substaion. What are the protection required for t..

Answer / ajay

for H.V side u can use R.M.U whc include SF6 C.B and For LT
side ACB

Is This Answer Correct ?

4 Yes

3 No

I decided to provide a 11KV / 440V Xformer in my Substaion. What are the protection required for t..

Answer / nirajan poudel

11000/440v means it is step-down transformer.so, for MV
side use 9kv LA,11 kvDO-FUSE and switch gear panel which
includes VCB which is used for isolating the transformer
during maintenance period.For LV side use TP MCCB for 3-
phase bus bar(R,Y,B) and use SP MCCB for 1-phase bus
bar.And there must be provision for AMF (Automatic Main
Failure Panel) to change the supply from main line to stand-
by generator and vice-versa with respective CB tripped.

Is This Answer Correct ?

1 Yes

0 No

I decided to provide a 11KV / 440V Xformer in my Substaion. What are the protection required for t..

Answer / ajay pal

transformer are to be fully earthed ,neutral grounding
resistor are to be provided, transformer overhead
differential protection , transformer oil for cooling is
very necessary ,

Is This Answer Correct ?

1 Yes

0 No

I decided to provide a 11KV / 440V Xformer in my Substaion. What are the protection required for t..

Answer / doli tomar

11000/440v means it is step-down transformer.so, for MV
side use 9kv LA,11 kvDO-FUSE and switch gear panel which
includes VCB which is used for isolating the transformer
during maintenance period.For LV side use 4P ACB /MCCB for
3-
phase bus bar(R,Y,B) and use overcurrent, overvoltage,
undervoltage,IDMT,Single phase preventer,restricted earth
fault relay because Relays are used where it is necessary
to control a circuit by a low-power signal (with complete
electrical isolation between control and controlled
circuits), or where several circuits must be controlled by
one signal.

Is This Answer Correct ?

0 Yes

0 No

I decided to provide a 11KV / 440V Xformer in my Substaion. What are the protection required for t..

Answer / rakesh

Transformer Secondary star neutral need to be earthed.
Separate earthing pit need to be provided.

Is This Answer Correct ?

3 Yes

6 No

Post New Answer

More Electrical Engineering Interview Questions

Draw a SLD for main panel for school having connected load of 1200kw and emergency generator 200kw.also show the increase of additional load of chiller 225kw in the lv panel indicating meter postion size of transformer ,cables and capacitor bank.

0 Answers

which braking is used in traction motor and what is its working send at mukeskumar27@hotmail.com

2 Answers

What is the function of a pressure Switch in a Substation?

2 Answers

why voltage coil in wattmeter called as pressure coil why the pressure term is used in wattmeter?

1 Answers NPCIL,

Synchrounous motor is three phase motor,but its not self starting .why?

23 Answers Delta Beverages, KI, L&T, NTC, TVS, Wipro,

describe the Operation of induction generators from bus bars

0 Answers AMIE,

difference between crane drive and line drive.