what are the inputs required for writing test cases

Satyam,

when you don't have time to write test cases, what do you do?

Satyam,

Could you pls give me sites where i can test card? mail me to

godaddy.com,

ATM REQUIREMENT TO BE TRANSLATED INTO TEST PLAN AND TEST CASES ATM REQUIREMENT AS FOLLOWS: Requirements Statement for Example ATM System The software to be designed will control a simulated automated teller machine (ATM) having a magnetic stripe reader for reading an ATM card, a customer console (keyboard and display) for interaction with the customer, a slot for depositing envelopes, a dispenser for cash (in multiples of $20), a printer for printing customer receipts, and a key-operated switch to allow an operator to start or stop the machine. The ATM will communicate with the bank's computer over an appropriate communication link. (The software on the latter is not part of the requirements for this problem.) The ATM will service one customer at a time. A customer will be required to insert an ATM card and enter a personal identification number (PIN) - both of which will be sent to the bank for validation as part of each transaction. The customer will then be able to perform one or more transactions. The card will be retained in the machine until the customer indicates that he/she desires no further transactions, at which point it will be returned - except as noted below. The ATM must be able to provide the following services to the customer: A customer must be able to make a cash withdrawal from any suitable account linked to the card, in multiples of $20.00. Approval must be obtained from the bank before cash is dispensed. A customer must be able to make a deposit to any account linked to the card, consisting of cash and/or checks in an envelope. The customer will enter the amount of the deposit into the ATM, subject to manual verification when the envelope is removed from the machine by an operator. Approval must be obtained from the bank before physically accepting the envelope. A customer must be able to make a transfer of money between any two accounts linked to the card. A customer must be able to make a balance inquiry of any account linked to the card. A customer must be able to abort a transaction in progress by pressing the Cancel key instead of responding to a request from the machine. The ATM will communicate each transaction to the bank and obtain verification that it was allowed by the bank. Ordinarily, a transaction will be considered complete by the bank once it has been approved. In the case of a deposit, a second message will be sent to the bank indicating that the customer has deposited the envelope. (If the customer fails to deposit the envelope within the timeout period, or presses cancel instead, no second message will be sent to the bank and the deposit will not be credited to the customer.) If the bank determines that the customer's PIN is invalid, the customer will be required to re-enter the PIN before a transaction can proceed. If the customer is unable to successfully enter the PIN after three tries, the card will be permanently retained by the machine, and the customer will have to contact the bank to get it back. If a transaction fails for any reason other than an invalid PIN, the ATM will display an explanation of the problem, and will then ask the customer whether he/she wants to do another transaction. The ATM will provide the customer with a printed receipt for each successful transaction, showing the date, time, machine location, type of transaction, account(s), amount, and ending and available balance(s) of the affected account ("to" account for transfers). The ATM will have a key-operated switch that will allow an operator to start and stop the servicing of customers. After turning the switch to the "on" position, the operator will be required to verify and enter the total cash on hand. The machine can only be turned off when it is not servicing a customer. When the switch is moved to the "off" position, the machine will shut down, so that the operator may remove deposit envelopes and reload the machine with cash, blank receipts, etc. The ATM will also maintain an internal log of transactions to facilitate resolving ambiguities arising from a hardware failure in the middle of a transaction. Entries will be made in the log when the ATM is started up and shut down, for each message sent to the Bank (along with the response back, if one is expected), for the dispensing of cash, and for the receiving of an envelope. Log entries may contain card numbers and dollar amounts, but for security will never contain a PIN.

Can any one send me the Sample sanity Test Cases??? Mail id:veerabhadrudu.p@gmail.com

TCS,

If I have written test cases for any application:there are 70-80 test cases and steps for writing test cases are common in some TCases.then May I have to write the repeated steps or May I write Repeat the steps of TC id so and so

If I wrote test cases for Login Window with test case Name Login window & test case id L_01.Now if Name of Login window get changed in the next version.then May I have to change the Test case name & Test case id OR HAVE TO block the previous test case and write the new one

If there are 10 steps for a test case. and for this test case there are 6 expected results. should I write 6 exp. results in the Expected Result column for a single tes case

do we write separate test cases for each type of testing? for example for functional testing and integration testing,we write two seprate test case documents or just one?please explain.

How about do we go as far as writing test cases is considered?

How should I maintain the test cases and Test Log for different versions/builds of the application.

Can test case contains more than 50 steps in single test case?

If there are 4 buttons New,Edit,Delete & Refresh for Item screen .May I have to write 4 different test cses for each button OR I can perform all operations[Create,Edit,Delete & refresh item] in a single tes case? Please reply as early as possible. It's very urgent to me

Can any one tell me how to write test data. i mean, to test each input, 2 test input(1 for +ve, & other for -ve) are given. so , for example, if i want to write test data for login form, how many test data should i write in test case?

Nike,

If I have written the 10 Positive test cases first and Negative test cases 11 to 25 .I Execute +ve first & then - ve as per test cases were written .Now if I got the next build & if I write again +ve Test Cases 26-30 first & then - ve 31-35 but I have to execute all test cases 1 to 35.But here the sequence of execution is +ve,-ve,+ve & -ve .How should I maintain the test cases .Please tell me It's Urgent .Thanks In Advance.....Tester

IBM,