Interested to Buy Any Domain ? << Click Here >> for more details...
Are Coils of Electromagnetic flowmeter in direct contact
with fluid material
- 4 Answers
- 8541 Views
- TATA, I also Faced
- E-Mail Answers
Answer Posted / www.islamqa.com
the answer is no.
actually magnetic flowmeter is based on Faraday's law, the magnet is prefered to be electrically produced and the polarity is reversed with timing to avoid flowing material polarization.
the electrodes/wires are in direct contact with the fluid material, as we consider the passing material is a series of consecutive fluid conductors.
Regards,
Ahmed Sabry
Control and Instrumentation Engineer
GPC - General Petroleum Company
ahmedsabry.online@gmail.com
CELL.: 00 2 0121367310
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
how to check earthing,what is minum ohms for proper earthing
how can leve transmetter calibate in feild .and also put cv and flow plz .....
If P will increase then what will happen with PID?
What are the types of valves?
what is temperature compensation?
What is hp & mp seperator .& what is its working principle ?
How to calibration a control valve?
What is the minimum rating availalbe for weld neck orifice in market?
how can i check vortex shedder bar it is ok? if there is ohms condition are shown correct?
POSSITIVE PULSE IS APPLIED TO AN INVERTER INPUT.THE TIME FROM THE LEADING EDGE OF THE INPUT TO THE LEADING EDGE OF THE OUTPUT IS 10 ns. THE TIME FROM THE TRAILING EDGE OF THE INPUT TO THE TRYLING EDGE OF THE OUTPUT IS 8 ns. WHAT ARE THE VALUES OF tPLH and tPHL?
What happen if I install my pressure transmitter below the elevation of pipe in natural gas service?
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
dear friends, i have seen flow as the selection critriea in presure guage (bourdon tube) and i would like to know what is the relation between flow and performance of pressure guage other parameters i found in the data sheet are pressure max. 1ksc temperature max. - 50 deg c line size - 80NB operating range - 1ksc pr. guage range - 0-2 ksc thank u,
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
how to calibrate and troubleshooting of leveltroll?
