how gearbox ratio was calculated?

Categories >> Engineering >> Mechanical Engineering
Suggest New Category

Question Posted / ajay

7 Answers
15496 Views
Reliance, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

how gearbox ratio was calculated?..

Answer / deependra singh parihar

The Speed Ratio for any given gear box is Calculated by
following relation

T1/T2 =N2/N1

so Speed of Driven or Follower gear will be

N2 = (T1/T2)*N1

Is This Answer Correct ?

46 Yes

4 No

how gearbox ratio was calculated?..

Answer / ramesh yerabolu

The speed of the gear box or no : of teeths of gears can be
calcullated by N1/N2=T2/T1. If you know three valves we can
find out the forth one.

Normally the GB ratio is mentioned in 5 :1,10:1 like.
Ex : GB ratio is 30 : 1 that means 30 revalutions of worm
shaft is equal to 1 revalution of worm wheel.

Is This Answer Correct ?

13 Yes

2 No

how gearbox ratio was calculated?..

Answer / mech09138

it is the ration of pinion speed/gear speed

Is This Answer Correct ?

3 Yes

0 No

how gearbox ratio was calculated?..

Answer / bharat

There is two types. .....
1 . Gear box
2 . Gear ratio.

For gearbox ratio you should know input rpm or torque and out put rpm or torque.

T1 / T2 = N2 / N1.

T1 = No. Of teeth on driven
T2 = No of teeth on driver
N2 = o/p rpm
N1 = I/p rpm

For finding gear ratio...

Ratio = T1 / T2.

Is This Answer Correct ?

2 Yes

0 No

how gearbox ratio was calculated?..

Answer / v.vinoth

n = (NS2-NS1)/(NS2+NR)

Is This Answer Correct ?

5 Yes

6 No

how gearbox ratio was calculated?..

Answer / unemployed

n2=t1/t2*n1 but with friction i.e
n2=t1/t2*n1+0

Is This Answer Correct ?

0 Yes

3 No

how gearbox ratio was calculated?..

Answer / shubankar sen

3:1

Is This Answer Correct ?

1 Yes

6 No

Post New Answer

More Mechanical Engineering Interview Questions

1.Difference between enthalpy & entropy?

3 Answers Covanta Energy, TATA,

should cutouts made in main header of metal ducting be deducted from duct measurement.

0 Answers BARC,

What is the advantage and disadvantage of IS 2062 Gr A over IS 2062 Gr B & C

3 Answers TATA,

Why manholes in vessels are usually elliptical in shape ?

1 Answers

When I use two metal wire dowsing rods and walk over the septic tank,(or any other place where the ground has been dug up) they swing apart. What force causes them to move? magnetic, electrical, other?

1 Answers

how airconditioner works

8 Answers Bhel,

why do we appoint u if we have software for same work?

3 Answers

We select 10mm nominal thickness for Elip head of a pressure vesel. The minimum thickness after forming is 8.2mm. (Shell thickness is 8mm. The minimum thickness after forming is satisfied or not with UG-79 (d)(3) in ASME SECTION VIII, Div.1?

0 Answers PetroVietnam,

describe a type when u anticipated potential problems and development of preventive measure.

0 Answers

what is diploma?

1 Answers Honda, Hyundai,

What is the use of metal jack plane?

0 Answers

two boilers producing 10 ton/h steam one has 8 bar and second on 5 bar which will consume more fuel? and why?

4 Answers

For more Mechanical Engineering Interview Questions Click Here