let there are three switch and there are 3 ree valn craed
on each switch that is vlan 2 on first switch valn 3 on 2nd
switch and vlan 4 is cretaed on switch 3
i have implemnted intervlan routin through ciso switchses.
the router is conected through its fa0/1 port by one switch
and and the two switch are trunked with each other
now question is that we want to comuniacte betwwen vlan but
does alse want that only vlan 2 is allow to access internet
(ISP)which is conected through s0 interface of router.and
no any vlan can access that internet.what should be
solution.
- 1 Answers
- 3095 Views
- I also Faced
- E-Mail Answers
Answer / jitendera kumar sinha
i am sending my own question solutions and answer might be
access-list
it has ask in one of my interviews and now i got the answer of that question
| Is This Answer Correct ? | 0 Yes | 1 No |
What is a characteristic of Store and Forward switches? A.) They work at wire speed. B.) They are the same as Cut-Through switching in 'prune' mode. C.) They forward based on transport layer info. D.) They forward the frame before it is completely read. E.) They increase latency.
Which of the following are examples of the Datalink Layer? A.) LLC B.) SQL C.) TCP D.) Token Ring E.) IP
Identify 3 characteristics of an IP address? A.) Contains a network portion and a host portion B.) 32 bits long C.) Unique to each network D.) Part of the default Cisco configuration E.) Referred to as the hardware address
What is the default size of a standard ping on a Cisco router? * A: 100 bytes * B: 32 bytes * C: 10 bytes * D: 16 bytes
How the STP determinw that which Port should be Root Port, which port should be Designeted Port , Blocking Port and Forwarding Port in Layer 2 STP topology........ Hi friends Thanks for posting the answer of above given questions i agree with all of you that BPDU is the Protocol that are used to determine this is clear to me.. But I want to Know the Process like Why it Blocked the port Fa0/1 Insted of Fa0/2 waiting for Answer Posting .... Thanks in Advance
What is the maximum request timer?
What is osi?
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# acess-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log
Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
What do you understand by ‘protocol’ in networking?
When we do default route?
CCNA 
